Mechanical Monitoring

Mechanical Monitoring for Chemical Plants

How chemical and process plants apply vibration analysis, lubrication monitoring, and condition-based maintenance to rotating equipment in corrosive environments, hazardous areas, and continuous-process operations.

The Environment Problem

Chemical plants operate equipment in conditions that accelerate every mechanical failure mode: corrosive atmospheres attack bearing surfaces, process fluids contaminate lubricants through worn seals, and thermal cycling from batch processes fatigues rotating components faster than steady-state service.

Asset Types Common in Chemical Plants

Chemical plants rely on a narrow set of rotating equipment types, each with distinct failure modes and monitoring requirements.

Large centrifugal compressors are often single-train installations with no installed spare. A compressor trip means a process unit trip. These machines typically run under API 670 protection systems with continuous proximity probe monitoring on shaft position. Condition monitoring supplements the protection system by detecting developing faults before they reach trip levels.

Reciprocating compressors used in hydrogen service, ammonia synthesis, and high-pressure applications run at relatively low speeds (typically 300 to 600 RPM) but generate complex vibration signatures from piston, valve, and crosshead motion. Valve wear is the most common failure mode and is detectable through vibration and cylinder pressure analysis.

Process pumps handling corrosive and abrasive fluids include vertical sump pumps, horizontal centrifugals, and magnetically coupled pumps. Mechanical seal failure is the primary maintenance event. Impeller wear from abrasive service (slurries, crystallizing fluids) reduces hydraulic performance before mechanical damage becomes apparent.

Agitators in reactor vessels present monitoring access challenges because the agitator shaft enters the vessel through a seal or stuffing box, and sensors may need to be mounted on the gearbox or motor rather than near the agitated fluid. Side-entry agitators can be monitored on the gearbox output shaft bearing. Top-entry agitators are monitored at the drive and gearbox, with shaft-end proximity probes on larger units.

Cooling tower fans typically run at low RPM with large blade spans. Blade imbalance from deposits or damage produces a strong 1x signature. Gearbox faults produce higher-frequency signatures that require sensors with adequate frequency response for the gear mesh frequency.

Corrosive Atmosphere Effects on Rotating Machinery

The chemical plant atmosphere introduces failure mechanisms that are absent in clean manufacturing environments.

Bearing corrosion from process gas leaks. Hydrogen sulfide in refinery and gas processing service attacks steel bearing components directly. Chlorine and hydrochloric acid vapors in chlor-alkali and PVC production corrode bearing surfaces and housings. Corrosion pitting on bearing raceways generates vibration signatures similar to fatigue spalling but progresses differently: the surface damage is chemical rather than stress-driven, and lubrication film is insufficient to protect corroded surfaces even when the lubricant itself is uncontaminated.

Seal degradation from process fluid exposure. Mechanical seals exposed to process fluids through face wear or thermal shock degrade faster in chemical service than in water service. Seal face material selection (silicon carbide, tungsten carbide, carbon) is critical for specific chemical services. A seal that begins to pass process fluid creates a contamination pathway for lubricant degradation.

Coupling and shaft corrosion. Exposed coupling elements, keyways, and shaft surfaces corrode in acidic atmospheres. Corroded couplings transmit misalignment vibration differently than clean couplings, which complicates vibration interpretation. Shaft surface corrosion under bearings can cause the inner race to creep on the shaft.

Hazardous Area Sensor Requirements

A large portion of chemical plant rotating equipment operates in classified hazardous areas (Zone 1 or Zone 2 under IEC 60079 / ATEX, or Division 1 or Division 2 under NEC). Sensors and associated electronics must be certified for the specific zone and gas group where they are installed.

ATEX and IECEx certification for vibration sensors covers the sensor body and cable entry. Zone 1 equipment must be certified Ex d (flameproof) or Ex ia (intrinsically safe). Zone 2 equipment permits Ex nA (non-sparking) or Ex ec (increased safety). Wireless sensors for Zone 1 typically require intrinsic safety barriers or are certified Ex ia for the radio transmitter as well as the sensor.

Intrinsically safe barriers limit the electrical energy available in the hazardous area to levels below ignition thresholds. Zener barriers and galvanic isolators serve this function for wired sensors. The associated apparatus (data acquisition hardware) is located in a safe area, connected through the barrier.

Verify that sensor certification matches the specific gas group and temperature class for your installation location. A sensor certified for IIA/IIB gas groups is not certified for hydrogen service (IIC). This is a compliance requirement, not a performance consideration.

Lubrication Challenges in Chemical Service

Contamination from process fluid ingress is the primary lubrication failure mode in chemical plants. A worn mechanical seal or damaged lip seal allows process fluid to enter the bearing housing. Even small quantities of water, solvents, or process gases degrade lubricant viscosity and film strength. Oil analysis programs that sample from the drain or via an oil port on the bearing housing detect water contamination, particle count increases, and viscosity change before bearing damage is advanced.

High-temperature applications in hot service compressors and process pumps require synthetic lubricants with high viscosity indexes and oxidation stability. Mineral oils degrade rapidly above 90 degrees C oil temperature. Polyalphaolefin (PAO) and polyalkylene glycol (PAG) synthetics extend service life significantly in high-temperature rotating equipment.

Lubricant selection for specific chemical service. Process gas environment can affect lubricant performance independent of contamination. Hydrogen dissolves in some lubricants under pressure, reducing viscosity when pressure drops suddenly. Ammonia attacks zinc-containing lubricant additives. Consult lubricant suppliers for compatibility with the specific process gases present in your plant before finalizing lubricant selection for compressors and pumps in chemical service.

Process-Critical Monitoring Priorities

Single-train reciprocating compressors represent the highest consequence failure point in many chemical and gas processing facilities. When there is no installed spare and the compressor serves a critical process unit, continuous monitoring is justified regardless of cost. The monitoring system should cover: cylinder pressure (for valve condition), piston rod vibration or displacement (for crosshead wear and packing condition), and crankshaft/bearing vibration.

Large centrifugal pump-compressor trains that drive continuous processes benefit from continuous online monitoring at the drive train bearings. Periodic route-based measurement is insufficient for machines where the consequence of an undetected fault is a production unit outage. The monitoring interval should be short enough to catch faults that develop in days, not weeks.

Applicable API Standards

API 670 covers machinery protection systems for large rotating machinery in petrochemical and refinery service. It defines requirements for proximity probes, velocity transducers, and accelerometers used in protection service, along with alarm and trip logic requirements. Condition monitoring systems on API 670 machinery must coexist with the protection system without interfering with trip functions.

API 618 covers reciprocating compressors for petroleum, chemical, and gas industry services. It defines mechanical requirements and, in its pulsation and vibration control annex, specifies limits for piping vibration and pulsation that inform where vibration monitoring is required on associated piping systems.

API 610 covers centrifugal pumps for petroleum, petrochemical, and natural gas industries. It defines acceptable vibration levels in terms of peak velocity at the bearing housing. Condition monitoring systems on API 610 pumps should alarm when vibration exceeds the limits defined in the applicable API 610 edition for the service class.

Chemical Plant Asset Monitoring Summary

Asset Type Primary Failure Mode Monitoring Approach Special Requirement
Large centrifugal compressor Seal and bearing failure; rotor rub Continuous proximity probe (API 670) plus bearing accelerometer Must not interfere with protection system trip logic
Reciprocating compressor Valve wear; packing wear; bearing wear Cylinder pressure analysis; piston rod vibration; crankcase vibration Low RPM requires sensors with sub-10 Hz response
Process pump (centrifugal) Mechanical seal failure; impeller wear; bearing failure Vibration at drive-end and non-drive-end bearings; temperature; barrier fluid monitoring ATEX/IECEx certification for hazardous area installations
Agitator Gearbox wear; shaft seal failure; bearing failure Vibration at gearbox input and output bearings; temperature Mounting access may be limited; side-entry vs. top-entry geometry differs
Cooling tower fan Blade imbalance from deposits; gearbox wear; bearing failure Vibration at motor and gearbox bearings; temperature High humidity environment; sensor and cable ingress protection required
Fired heater fan (forced or induced draft) Blade erosion from combustion products; bearing failure at elevated temperature Vibration at drive-end and non-drive-end bearings; temperature High-temperature rated sensors required for FD/ID fan bearing temperatures

Condition Monitoring for Chemical Plant Assets

Wireless vibration and temperature sensors rated for industrial environments. Automatic fault detection for pumps, compressors, fans, and agitators. Hazardous area certification inquiries handled through Tractian's solutions team.

See Mechanical Monitoring
mechanicalmonitoring.com is an independent resource covering rotating equipment monitoring and condition-based maintenance. Product references are for informational purposes only. Verify all specifications with the vendor before purchasing. mechanicalmonitoring.com is operated by Tractian; see tractian.com for full product details.