Mechanical Monitoring Tool

Bearing Relubrication Interval Calculator

Calculate grease relubrication intervals for rolling element bearings using the SKF industry formula, adjusted for operating conditions including temperature, contamination, and shaft orientation.

Key Insight

Over-lubrication causes as many bearing failures as under-lubrication. Too much grease overheats the bearing; too little leaves the rolling elements unprotected. This calculator provides a starting-point interval based on speed, size, and operating conditions, to be verified against your bearing manufacturer's data.

⚠ Estimate Only: Verify Against Manufacturer Data

This tool provides estimates based on an industry formula, not manufacturer-specific data. Relubrication intervals vary by grease type, bearing type, and application. Always verify against your specific bearing manufacturer's published relubrication tables before establishing a maintenance schedule.

Estimate Only

Calculate Relubrication Interval

Rotational speed of the shaft in revolutions per minute
Inner ring bore diameter: the d dimension from the bearing designation
Axial width of the bearing: used to estimate grease quantity per relubrication

Correction Factors: Operating Conditions

Each selected factor reduces the base relubrication interval. Select all that apply.

Relubrication Interval Results
ESTIMATE ONLY. This formula provides a starting point. Always verify against your bearing manufacturer's published relubrication data and cross-reference with your grease supplier's recommendations for the specific grease type and NLGI grade in use.

The Science Behind Relubrication Intervals

Bearing relubrication interval depends on how fast the bearing runs and how large it is. These two factors determine how hard the grease is working. At high speeds, grease is mechanically worked more intensively. The rolling elements churn through it continuously, generating heat and gradually breaking down the thickener structure. Larger bearings have more rolling element contact area, which means more grease is needed and the grease in any one region is replenished less frequently by the motion of the bearing.

The SKF formula captures this relationship through the speed factor nDm, where n is shaft speed in RPM and Dm is the mean bearing diameter. As this product increases, the relubrication interval falls, sometimes sharply. A bearing running at 3,000 RPM with a 60mm bore may need relubrication six times more frequently than the same bearing running at 500 RPM. This is why one-size-fits-all PM intervals are a maintenance liability. A plant using the same relubrication schedule for all motors of similar size will over-lubricate slow-running equipment and starve fast-running equipment.

Operating conditions compound the speed-and-size relationship. High temperature accelerates oil bleed from the thickener, leaving a dry cake that no longer protects the rolling elements. Contamination from dust or moisture dilutes and degrades the grease, shortening its effective life. Vertical shafts lose grease downward under gravity, creating a lean zone at the upper races. Each of these conditions is addressed in the SKF formula through correction factors that proportionally reduce the calculated interval.

The consequences of getting this wrong are symmetric. Under-lubrication starves the rolling elements of the protective film they need, accelerating fatigue and surface damage, eventually leading to spalling, cage fracture, and seizure. Over-lubrication is equally damaging. Excess grease builds pressure inside the bearing housing, forces seals outward, increases operating temperature as rolling elements churn through the grease, and can introduce contamination if the housing vents or seals fail under pressure. A correct interval, verified against manufacturer data, protects against both failure modes.


Correction Factors Explained

Vertical Shaft Orientation (×0.5)

In horizontal applications, grease redistributes relatively evenly around the bearing under operation. On a vertical shaft, gravity continuously pulls the grease toward the lower race. The upper portion of the bearing runs progressively leaner between relubrication events. Halving the interval compensates by restoring grease before the upper zone is fully depleted.

High Vibration (×0.5)

Vibration above approximately 0.2g mechanically works grease at a higher rate than normal operation. This accelerates oil separation from the thickener, degrades consistency, and can cause migration out of the bearing cavity. Equipment with high background vibration (reciprocating compressors, impact machinery, fans on unbalanced rotors) requires more frequent grease replenishment.

Contaminated Environment (×0.5)

Dust, fine particulates, and water ingress mix with grease and reduce its protective film strength. Contaminated grease also has higher abrasive potential, accelerating wear on rolling elements and races. Environments with sawdust, cement dust, metal fines, steam, or wash-down water require conservative intervals and sealed or shielded bearing configurations wherever possible.

Elevated Temperature 70–80°C (×0.5)

Grease oxidizes faster at higher temperatures. In this range, the base oil begins to bleed from the thickener more rapidly, reducing lubricant film thickness between relubrication events. Operating continuously at 70–80°C roughly halves the effective grease service life versus a standard 40–50°C application.

Temperature Above 80°C (×0.25)

Above 80°C, most standard greases degrade rapidly. Oxidation rates increase nonlinearly, thickener structure breaks down, and evaporation of lighter base oil fractions accelerates. At these temperatures, intervals must be reduced to one quarter of the base calculation, and the grease type selection becomes critical. Standard lithium soap greases may not be suitable at all without a specific high-temperature rating.

Food-Grade or Specialty Grease (×0.5)

H1-certified food-grade greases are formulated with white mineral or synthetic base oils and permitted thickeners, not for performance optimization. They typically have lower load capacity and shorter service life than equivalent industrial greases. Specialty greases for extreme environments may also have operating range limitations that require more conservative scheduling.


The SKF Relubrication Formula

tf = K × (14,000,000 / (n × √d) − 4 × d) Where: tf = relubrication interval (hours) n = shaft speed (RPM) d = bearing bore diameter (mm) K = combined correction factor (product of all applicable multipliers) Grease quantity per relubrication: G = 0.005 × d × B (grams) B = bearing width (mm) Base K = 1.0 Correction multipliers (cumulative): Vertical shaft × 0.5 High vibration (>0.2g) × 0.5 Contaminated env. × 0.5 Temperature 70–80°C × 0.5 Temperature >80°C × 0.25 (overrides 70–80°C) Food-grade grease × 0.5
Sources and References SKF relubrication formula as published in the SKF Bearing Maintenance Handbook and SKF General Catalogue. Correction factor methodology consistent with SKF and major bearing manufacturer guidance. Also referenced in ISO 281:2007 (Rolling bearings: Dynamic load ratings and rating life) supplementary guidance. The grease quantity formula G = 0.005 × d × B is the SKF rule of thumb for open bearings without seals.
Estimate Only: Verify Against Manufacturer Data Relubrication interval depends on grease type (NLGI grade, base oil viscosity, thickener type), exact bearing type, sealing configuration, and application-specific conditions not fully captured in this formula. Do not use this result as a final maintenance schedule without cross-referencing your bearing manufacturer's published relubrication tables. Wrong relubrication intervals are a leading cause of premature bearing failure.
Tools on this site are provided for educational purposes only. Calculations are based on published engineering formulas and industry standards cited on each tool. Results do not constitute professional engineering advice. Do not make maintenance, safety, or operational decisions based solely on these outputs. Always verify results against your equipment manufacturer's documentation and consult a qualified engineer or reliability professional before acting. This site accepts no liability for decisions made using these tools.