Bearing failure is almost never random. Each failure mode has a specific root cause: wrong lubricant, overload, contamination, installation damage, or electrical discharge. Identifying the failure mode from the damaged bearing determines the root cause, which determines the corrective action that prevents recurrence.
ISO 15243: The Standard Classification
ISO 15243 provides the internationally accepted framework for classifying rolling element bearing failures. It defines six primary failure modes, each with distinct sub-categories, visual characteristics, and underlying causes. The standard exists because the same visible outcome, a damaged raceway, can result from very different root causes that require completely different corrective actions.
Replacing a failed bearing without identifying the failure mode and its cause virtually guarantees the replacement bearing fails the same way, often faster because the underlying condition is still present. A root-cause-first approach to bearing failure analysis is the only approach that prevents recurrence.
Failure Mode 1: Sub-Surface Fatigue (Spalling)
What It Is
Sub-surface fatigue is rolling contact fatigue driven by cyclic Hertzian stress beneath the rolling contact surface. Every time a rolling element passes over a point on the raceway, it compresses the material and creates a stress field that peaks slightly below the surface. Over millions of load cycles, this repeated stress initiates micro-cracks at stress concentration points: material inclusions, voids, or surface irregularities in the steel.
The cracks propagate parallel to the surface initially, then branch upward. When a crack reaches the surface, a fragment of material breaks free, leaving a pit or spall. The spall edges create further stress concentrations, and the damage propagates across the raceway.
Root Causes
- End-of-life fatigue: Normal fatigue at or beyond the calculated L10 bearing life. No defect in design or operation, the bearing has simply reached its design limit.
- Overloading: Radial or axial loads exceeding the bearing's rated capacity increase the peak Hertzian stress and dramatically reduce fatigue life. Fatigue life is roughly proportional to the inverse cube of the load for ball bearings (inverse power of 10/3 for roller bearings).
- Misalignment: Shaft or housing misalignment concentrates load at the edge of the raceway (edge loading), producing stress levels far higher than the uniform load the bearing was rated for.
- Improper installation: Shock loads during installation, such as hammer blows applied through the rolling elements rather than the ring, pre-stress the raceway and create the initial defects that become fatigue initiation points.
- Contamination: Hard particles that pass through the rolling contact dent the raceway surface. Each dent is a stress concentration point that initiates fatigue earlier than the clean-condition L10 life predicts.
Detection
Sub-surface fatigue is detectable by vibration analysis before visible damage becomes large. The developing spall creates an impulse each time a rolling element passes over it, generating vibration at the bearing fault frequencies: BPFO (ball pass frequency, outer race) for outer raceway defects, BPFI for inner raceway defects. Early-stage defects appear as sidebands around these frequencies in the frequency spectrum, and as elevated kurtosis in the time waveform. As the spall grows, broadband noise increases and the fault frequencies become more prominent.
Envelope analysis (demodulation of the high-frequency vibration signal) is the most sensitive technique for detecting early-stage spalling before the damage is visible to the eye.
Prevention
- Size bearings to the actual load, including dynamic and shock load components, not just the static nominal load.
- Use precision alignment methods: laser alignment to within manufacturer tolerances before startup.
- Use proper installation tools: hydraulic mounting tools or induction heaters for interference-fit bearings. Never apply installation force through rolling elements.
- Maintain contamination control: correct seal selection for the environment, proper filtration for oil-lubricated systems.
- Monitor vibration continuously on critical assets to detect spalling initiation weeks or months before failure.
Failure Mode 2: Surface Distress
What It Is
Surface distress is surface-origin fatigue caused by inadequate lubricant film thickness. When the film is too thin, the microscopic surface asperities (peaks in the surface roughness) of the rolling elements and raceways contact each other directly. This asperity contact generates local stress concentrations at the surface rather than below it.
The progression has three stages. First, micro-pitting: thousands of tiny pits form where asperities have collided, giving the surface a frosted or matte appearance under inspection. Second, smearing: under combined sliding and rolling contact (common during acceleration, deceleration, or speed changes), material transfers between surfaces. The smeared surface shows streaks of plastically deformed material. Third, gross surface damage as pitting and smearing coalesce.
Root Causes
- Incorrect lubricant viscosity: Viscosity too low for the operating speed and load means the film is too thin to separate the surfaces. The required minimum viscosity is calculated from bearing speed (in mm/s kinematic viscosity as a function of pitch diameter and rpm) and is specified in bearing manufacturer datasheets.
- Excessive operating temperature: Lubricant viscosity decreases with temperature. A lubricant correctly specified at ambient conditions may become too thin at elevated operating temperatures caused by high loads, inadequate cooling, or external heat sources.
- Water contamination: Water reduces lubricant viscosity, disrupts additive packages, and accelerates surface corrosion that roughens the raceway surface, making the lubrication film even less effective.
- High sliding velocity: Bearings with significant sliding contact (thrust bearings under combined loading, needle bearings) are more susceptible to smearing than pure rolling contact bearings under the same film conditions.
Detection
Micro-pitting appears as a frosted or chalky surface visible under 10x magnification. Smearing shows as directional streaks on rolling element or raceway surfaces. Vibration signatures for surface distress are less specific than spalling signatures: elevated broadband noise in the high-frequency range, increasing noise floor across the spectrum.
Lubricant analysis is often more diagnostic than vibration for early-stage surface distress: elevated metal particle counts (iron from raceways, chromium from rolling elements) with particle morphology showing rubbing or sliding wear particles rather than fatigue flakes.
Prevention
- Select lubricant viscosity using the bearing manufacturer's viscosity ratio (kappa) method. Target kappa greater than 1 under operating conditions (actual viscosity exceeds minimum required viscosity).
- Use extreme pressure (EP) additives when kappa is marginal or operating conditions are severe.
- Monitor and control lubricant temperature, and review bearing loads if temperature consistently exceeds lubricant specifications.
- Use water-resistant grease formulations in humid or washdown environments.
Failure Mode 3: Wear
What It Is
Wear is progressive material removal from the rolling and sliding surfaces, distinct from fatigue in that it does not originate from cyclic stress cycling below the fatigue limit. ISO 15243 identifies two wear mechanisms: abrasive and adhesive.
Abrasive wear occurs when hard particles in the lubricant or contaminant ingress scratch the rolling surfaces. The scratches follow the direction of rolling or sliding motion. Severe abrasive wear produces a roughened surface with directional scoring, increasing internal clearance and reducing the bearing's load-carrying capacity.
Adhesive wear occurs when metal-to-metal contact under inadequate lubrication causes material to transfer between surfaces. The surfaces weld microscopically at contact points and then tear apart as sliding continues. Adhesive wear produces a torn, rough surface with material transfer visible between rolling elements and raceways.
Root Causes
- Contamination ingress: Solid particles entering the bearing from the environment. Hard particles (silica, metal chips, scale) cause abrasive wear. The particle size relative to the lubricant film thickness determines severity: particles larger than the film thickness that can enter the rolling contact zone cause the most damage.
- Damaged seals: Seals that are cut, worn, or installed incorrectly allow contamination ingress. The wrong seal type for the application (lip seal in a high-speed application, non-contact seal in a contaminated environment) allows particles to bypass the seal.
- Lubrication failure: Grease depletion, incorrect relubrication intervals, or contaminated lubricant causes adhesive wear when the film breaks down completely.
- Relubrication with contaminated grease: Grease contaminated at the source, from an open container, or from a dirty grease gun introduces particles directly to the rolling surfaces.
Detection
Wear increases internal bearing clearance over time, which changes the vibration signature: increased vibration amplitude across a broad frequency range, with the shaft running noisier and with more play. Lubricant particle analysis detects wear debris early: elevated iron, chromium, and silicon (from abrasive particles) in oil analysis, or metallic contamination in used grease samples.
Vibration trending shows a gradual increase in overall vibration rather than the distinct fault frequency signatures characteristic of spalling.
Prevention
- Select the correct seal type for the environment: contact seals (RS, 2RS) for contaminated or humid environments; non-contact seals (RZ, 2RZ) only where friction must be minimized and contamination is low.
- Inspect seals at every maintenance interval and replace when damaged.
- Store and handle grease in sealed containers; use dedicated grease guns for each lubricant type.
- Implement oil filtration appropriate to the application: target ISO cleanliness codes from the bearing manufacturer for oil-lubricated systems.
Failure Mode 4: Corrosion
What It Is
ISO 15243 identifies three distinct corrosion mechanisms that affect bearings differently and have different root causes.
Moisture Corrosion
Water ingress causes rust pitting on raceways and rolling elements. Rust pits act as stress concentration points for fatigue, accelerating the onset of sub-surface fatigue. Corroded raceways show reddish-brown staining with pitting that follows the rolling track. Corrosion is common in equipment that sits idle in humid environments, in washdown applications with inadequate sealing, and in bearings where condensation forms from temperature cycling.
Fretting Corrosion
Fretting corrosion occurs at the interface between a bearing ring and its housing or shaft seat. Under alternating load, micro-motion occurs between the stationary surfaces that should be interference-fitted. This micro-motion breaks down the oxide layer on the mating surfaces, and the resulting fine metal particles oxidize to form reddish-brown (iron oxide) debris. The debris is abrasive, and the loss of material from the fretting zone reduces the interference fit, allowing more micro-motion and accelerating the process.
Fretting corrosion is identifiable by reddish-brown powder between the bearing ring and the shaft or housing bore. It is common in applications with heavy vibration loads, inadequate interference fit, or housings that flex under load.
Electrical Erosion
When electrical current passes through a bearing, it discharges through the thin lubricant film at the rolling contact points. Each discharge melts and re-solidifies a tiny volume of material, creating a micro-crater. The pattern depends on current type.
DC current creates a regular pattern of parallel craters across the raceway, forming a washboard or fluting appearance. This is the classic signature of electrical bearing damage from variable frequency drives (VFDs) without shaft grounding. AC current creates a random frosted appearance from irregular micro-discharges.
The voltage threshold for discharge depends on lubricant film thickness. In well-lubricated bearings, discharge occurs at 0.5 to 1 volt across the bearing. Even low voltages from stray currents can cause electrical erosion over time.
Root Causes by Type
- Moisture corrosion: Inadequate sealing, water ingress during cleaning or operation, condensation from temperature cycling in idle equipment.
- Fretting corrosion: Insufficient interference fit, excessive housing flexibility, high vibration loads, or tapered shaft fitting without lock nut pre-load.
- Electrical erosion: Variable frequency drives conducting stray current through the shaft and bearing to ground; welding current conducted through the machine frame; static charge buildup in belt-driven systems.
Prevention
- Use water-resistant or waterproof grease (NLGI 2 lithium complex or polyurea base) in humid or washdown environments.
- Verify interference fit per manufacturer specifications; use housing material with appropriate stiffness for the load.
- Install shaft grounding rings (carbon fiber brush rings) on VFD-driven motors to provide a low-resistance path to ground that bypasses the bearing.
- Use ceramic hybrid bearings (ceramic rolling elements) on the drive end of VFD motors to electrically isolate the shaft from the housing.
- Protect idle equipment from condensation by maintaining temperature above the dew point or by using desiccant protection during storage.
Failure Mode 5: Plastic Deformation
What It Is
Plastic deformation is permanent deformation of the raceway surface without fracture, caused by stresses that exceed the material's yield strength. ISO 15243 distinguishes two types: brinelling and false brinelling.
Brinelling (True Brinelling)
Brinelling is permanent indentation of the raceway from a static overload. The load at the rolling element contact point exceeds the yield strength of the raceway material, and the raceway permanently deforms inward. The result is a series of indentations spaced exactly at the rolling element pitch, with sharp edges and depths proportional to the magnitude of the overload.
Common causes include: hammer blows to the shaft or housing during installation or removal, shock loads from dropping assembled equipment, pressing operations that apply force through the rolling elements rather than directly to the ring being installed, and inadequate support of heavy shafts during bearing installation.
As the bearing rotates, rolling elements pass over the brinell impressions and generate vibration at frequencies corresponding to the impression spacing. The vibration signature is similar to spalling damage but the damage appears as clean, regular impressions rather than rough pits.
False Brinelling
False brinelling is wear damage that produces impressions visually similar to brinelling but with a different mechanism and different appearance. It occurs when a stationary bearing is subjected to vibration from nearby operating machinery, transport, or structural vibration. The rolling elements oscillate through a very small arc without completing a full revolution.
This micro-motion breaks down the lubricant film at the contact point and causes micro-adhesive wear at the stationary contact zone. The result is a polished or frosted indentation at each rolling element contact point, often with reddish-brown fretting oxide debris in the indentation. The edges are smooth rather than sharp, distinguishing false brinelling from true brinelling on inspection.
False brinelling is common in: spare bearings stored near vibrating equipment, equipment on extended standby near operating machinery, machines transported by truck or rail while assembled, and turbines that turn slowly on turning gear while adjacent units operate.
Prevention
- Brinelling: Use proper installation tools that apply force directly to the ring being mounted. For shaft-mounted bearings (inner ring interference), use a mounting sleeve that contacts the inner ring only. Never use a hammer directly on the bearing. Apply installation force parallel to the shaft axis.
- False brinelling: Rotate standby equipment periodically to move rolling elements to a new contact position. Use anti-fretting compounds (molybdenum disulfide or copper-based) on raceways of stored or idle bearings. Isolate spare bearing storage from nearby vibration sources.
Failure Mode 6: Fracture and Cracking
What It Is
Fracture is complete separation of a component (ring, rolling element, or cage) into two or more pieces. Cracking is partial separation that has not yet progressed to complete fracture. ISO 15243 identifies three sub-types based on the mechanism: forced fracture, fatigue fracture, and thermal cracking.
Forced Fracture
Forced fracture results from a single overload event that exceeds the fracture strength of the material. It occurs most commonly during installation (hammer blow that fractures the ring), during equipment impact events (crash stops, dropped tooling), or from incorrect fits that crack a ring as it expands or contracts onto a shaft or into a housing.
Fracture surfaces from forced overload show a rough, irregular texture without the propagation marks characteristic of fatigue fracture. The fracture line runs transverse to the ring or through the rolling element in the direction of the applied force.
Fatigue Fracture
Fatigue fracture begins as a crack initiated at a stress concentration (existing defect, corrosion pit, machining mark, or material inclusion) and propagates under cyclic load until the remaining cross-section can no longer support the load. The fracture surface shows beach marks or striations that trace the crack propagation path, distinguishing it from forced fracture.
Cage fatigue fracture is a specific sub-category: cages can fracture from cyclic loads if overloaded (more rolling elements than the cage can support), from excessive speed, from lubricant starvation causing cage-to-rolling-element friction, or from cage material degradation in chemically aggressive environments.
Thermal Cracking
Thermal cracking results from rapid temperature changes that create steep thermal gradients and differential thermal expansion stresses in the bearing material. It can occur when a hot bearing is quenched with cold water during maintenance, when a bearing is overheated by localized friction and then rapidly cooled, or from excessive heat generated by electrical discharges concentrating at a point on the raceway.
Thermal cracks run circumferentially around the ring (parallel to the rolling direction) or radially from the raceway surface inward, following the steepest thermal gradient.
Prevention
- Use induction heaters or oil bath heating for interference-fit bearing installation. Never exceed the maximum recommended temperature (typically 120 degrees C) to avoid tempering the steel and changing its hardness.
- Select bearings with adequate static load capacity for the maximum instantaneous load, including shock load factors.
- Specify correct fits: excessive interference fit can fracture a ring if the housing bore tolerance is at the tight end of its range.
- Never quench a hot bearing with water for rapid cooling; allow natural cooling or use controlled forced air.
- Inspect for cracking with magnetic particle testing or dye penetrant testing at overhaul intervals in critical applications.
Comprehensive Failure Mode Reference Table
| Failure Mode | ISO 15243 Category | Visual Appearance | Root Causes | Prevention | Vibration Signature |
|---|---|---|---|---|---|
| Sub-surface fatigue (spalling) | Rolling contact fatigue | Pits and spalls with rough, cratered edges on raceway; follows rolling track | End-of-life fatigue; overloading; misalignment; contamination dents; improper installation | Correct bearing sizing; laser alignment; proper installation tools; contamination control; continuous vibration monitoring | BPFO, BPFI, BSF fault frequencies; sidebands; kurtosis elevation; broadband noise as damage spreads |
| Surface distress (micro-pitting / smearing) | Surface fatigue | Frosted or matte surface (micro-pitting); directional streaks with material transfer (smearing) | Lubricant viscosity too low; excessive operating temperature; water contamination in lubricant | Viscosity selection using kappa ratio method; EP additives; temperature control; water-resistant lubricant | Elevated broadband noise; increasing noise floor; less specific than spall frequencies |
| Wear (abrasive / adhesive) | Wear | Directional scratches (abrasive); torn, rough surface with material transfer (adhesive); increased internal clearance | Contamination ingress; damaged seals; lubricant failure; contaminated grease | Correct seal selection; seal inspection; clean lubricant handling; oil filtration to target ISO cleanliness code | Gradual broadband vibration increase; noisy, play-related vibration; no specific fault frequency |
| Corrosion (moisture / fretting / electrical) | Corrosion | Rust pitting (moisture); red-brown oxide debris at ring seat (fretting); washboard or frost pattern on raceway (electrical) | Water ingress; insufficient interference fit; VFD stray current; welding current; static discharge | Water-resistant grease; correct fits; shaft grounding rings; ceramic hybrid bearings on VFD motors | Rust pitting: spall-type frequencies once pits initiate fatigue. Electrical: frosting produces broadband noise; fluting produces regular vibration at ball-pass frequencies |
| Plastic deformation (brinelling / false brinelling) | Plastic deformation | Sharp-edged regular impressions at rolling element pitch (brinelling); smooth polished indentations with oxide debris (false brinelling) | Installation shock loads; transport vibration; standby near operating machinery; inadequate lubricant at stationary contact | Proper installation tooling; anti-fretting compounds; periodic rotation of standby equipment; vibration isolation of stored bearings | Vibration at impression-spacing frequency as rolling elements pass over indentations; similar to spalling signature |
| Fracture and cracking | Fracture | Complete ring or element separation (forced: rough irregular face; fatigue: beach marks; thermal: circumferential or radial cracks) | Installation overload; single impact event; incorrect fits; cyclic load on existing defect; thermal shock from quenching | Induction heating for installation; correct fit specification; avoid cold-water quenching; magnetic particle or dye penetrant inspection at overhaul | Catastrophic: sudden high-amplitude broadband noise; often no advance warning distinguishable from other modes |
Contamination Types and Their Effects
| Contamination Type | Entry Mechanism | Effect on Bearing | Prevention |
|---|---|---|---|
| Hard particles (silica, metal chips, scale) | Inadequate or damaged seals; contaminated lubricant; installation in dirty environment | Abrasive wear on raceways and rolling elements; denting that initiates premature fatigue; increased internal clearance | Correct seal type and condition; ISO cleanliness-coded lubricants; clean work environment during installation; flush housing before installation |
| Soft particles (rubber seal debris, fibres) | Seal degradation; process contamination in open bearings | Lubricant degradation; partial blocking of lubrication passages; mild abrasion | Inspect and replace seals before degradation becomes contamination; use sealed bearings in fibrous process environments |
| Water | Washdown ingress; condensation from temperature cycling; steam environments | Lubricant film disruption (reduced viscosity); corrosion pitting; additive breakdown; hydrogen embrittlement of steel under severe cases | Water-resistant grease formulations; sealed or shielded bearings; positive pressure or labyrinth seals in washdown environments; relubricate after water exposure is confirmed |
| Chemical contaminants (acids, solvents, process fluids) | Process ingress; cleaning agent residue; reaction with grease additives | Lubricant chemical degradation; surface corrosion and pitting; cage material attack (polyamide cages vulnerable to acids and high-temperature grease) | Positive pressure sealing in chemical process environments; compatible lubricant and cage materials; regular oil analysis to detect chemical contamination early |
| Electrical discharge products | VFD common-mode current; welding; static discharge | Lubricant carbonization at discharge points; metallic debris from erosion craters in lubricant; raceway surface damage | Shaft grounding rings; ceramic hybrid bearings; insulated bearing housing on non-drive end; regular lubricant sampling for metallic content |
| Wear debris (self-contamination) | Generated internally by initial abrasive or adhesive wear; introduced during relubrication without purging old grease | Accelerates existing wear; metallic particles are harder than raceway steel and cause secondary abrasive damage; cascading failure | Purge old grease during relubrication; use grease-relief fittings; investigate and correct the primary contamination source, not just the secondary wear |
Post-Failure Bearing Analysis: Process
A post-failure analysis is only useful if it is done systematically before any cleaning, handling, or evidence is lost. The following process produces a finding that can be acted on.
Step 1: Photograph Before Touching
Photograph the failed bearing in the housing before removal, if possible. Document the housing condition, any contamination visible around the seal, lubricant color and consistency, and any staining on the shaft. Once removed, photograph all bearing surfaces before cleaning: the raceways on both rings, the rolling elements, the cage, and the bore and outer ring seat surfaces. The debris in the lubricant often identifies the failure mode: reddish oxide powder points to fretting corrosion, black carbon-like debris suggests electrical erosion, metallic particles indicate wear, and material fragments indicate spalling or fracture.
Step 2: Identify the Failure Mode
Using the visual characteristics in this reference, identify the primary failure mode. Look at the pattern, location, and texture of the damage. Ask: is the damage on the raceway, on rolling elements, on the cage, or on the ring seat? Is it concentrated in one location or distributed uniformly? Is the damage surface rough (fatigue or wear) or has it transferred material (adhesive, smearing, fretting)?
One failed bearing may show evidence of multiple failure modes. Identify the primary mode (the one that initiated failure) and the secondary modes (which developed because the primary failure changed the operating conditions). For example, initial electrical erosion roughening the raceway leading to secondary abrasive wear from the resulting metallic debris.
Step 3: Trace the Root Cause
Each failure mode maps to a specific set of root causes. For each candidate root cause, look for physical evidence that confirms or eliminates it. Spalling at end of calculated life: check maintenance records for bearing age. Spalling before design life: check alignment records, load calculations, and contamination controls. Fretting corrosion: check fit tolerances and housing bore measurement. Electrical erosion: check VFD specifications and shaft grounding installation.
Do not stop at the failure mode. The root cause is what gets corrected before the replacement bearing is installed.
Step 4: Implement the Corrective Action
Correct the root cause before installing the replacement bearing. If contamination caused the failure: clean the housing completely, inspect and replace the seal, and verify the lubricant supply is uncontaminated. If misalignment caused premature spalling: realign the shaft before startup. If electrical current caused erosion: install and verify the shaft grounding ring before the motor is returned to service. Installing the same bearing type into the same uncorrected condition produces the same failure.
Step 5: Document and Track
Record the failure mode, root cause, corrective action, and the replacement bearing details in the equipment maintenance record. Track bearing life on repeat failures: if the same failure mode appears on successive replacement bearings at the same machine, the root cause has not been fully corrected. Recurring failure at a specific asset is diagnostic evidence that the corrective action was incomplete.
Detect Bearing Failures Weeks Before They Happen
Tractian's continuous vibration monitoring identifies spalling, surface distress, and wear at initiation, not after catastrophic failure.
See Mechanical Monitoring