Mechanical Monitoring

Lubrication Monitoring

Lubrication monitoring tracks grease and oil condition on rotating equipment, providing the data to relubricate at the right time rather than on a fixed calendar schedule that ignores actual operating conditions.

Key Insight

Most bearing failures trace back to lubrication problems: wrong lubricant, too little grease, too much grease, or relubrication intervals that ignore operating temperature and speed. Lubrication monitoring replaces calendar-based guessing with condition-based relubrication.

Why Lubrication Matters for Machine Reliability

Lubrication creates and maintains the elastohydrodynamic film that separates rolling elements from raceways. When the film is adequate, the bearing rolls on a thin layer of pressurized lubricant and metal-to-metal contact is minimal.

When the film breaks down, surface asperities contact directly, generating heat, friction, and wear debris. The progression from film breakdown to bearing failure can happen in hours under severe conditions or over months in normal service.

The film thickness depends on lubricant viscosity, operating speed, load, and temperature. Change any of these variables without adjusting the lubrication strategy and the film margin shrinks. Most fixed-interval schedules are set for average conditions and miss peaks: a motor running hotter in summer, a pump cycled harder during a production push, a gearbox carrying increased load after a process change.

Failure Modes from Lubrication Problems

Each failure mode has a distinct cause and distinct early indicators. Identifying which mode is active determines the correct corrective action.

Failure Mode Cause Early Indicator
Under-lubrication Inadequate grease volume, interval too long, grease degraded Ultrasound amplitude rise, bearing temperature increase
Over-lubrication Excessive grease volume causing churning and heat generation Bearing temperature spike after relubrication, ultrasound "rushing" sound
Contamination Incorrect grease, mixing incompatible greases, ingress of water or particles Oil analysis: increased particle count, water content above 500 ppm, viscosity change
Grease separation Incorrect NLGI grade, high temperature operation, extended storage Oil bleed from grease fitting, loss of consistency
Oxidation Grease exposed to heat above its upper temperature limit for extended periods Oil analysis: increased acid number, darkening, viscosity change

Over-lubrication is the most common mistake. Technicians following a time-based schedule add grease regardless of current condition. The excess grease heats up from churning, accelerating oxidation and shortening bearing life. The bearing that "got more grease" fails faster than the one left alone.

Ultrasound for Lubrication Monitoring

Ultrasound is the most direct feedback mechanism for grease-lubricated bearings. The technique detects high-frequency acoustic emissions from bearing surfaces in the 20 kHz to 100 kHz range, well above audible noise from surrounding equipment.

The procedure: take an ultrasound baseline reading on a bearing in known good lubricated condition. Before each relubrication, take a reading to confirm condition. During relubrication, add grease slowly while monitoring ultrasound amplitude. Stop when amplitude returns to baseline or when new grease appears at the relief point.

This prevents both under- and over-lubrication in a single procedure. The technician has real-time feedback instead of following a volume estimate from a chart.

What the Sounds Indicate

A well-lubricated bearing produces a smooth, consistent hiss in the heterodyne output. An under-lubricated bearing produces friction noise with higher amplitude in dBuV. An over-lubricated bearing produces a rushing or turbulent sound from grease churning, with amplitude often elevated above baseline after adding grease.

These audio cues, combined with amplitude measurements, give technicians real-time feedback during the relubrication process. The amplitude reading before relubrication tells you whether to add grease. The reading during relubrication tells you when to stop.

Amplitude Trend Analysis

Beyond point-in-time readings, trending amplitude over time reveals how quickly a bearing's lubrication condition degrades between intervals. A bearing that drops to elevated amplitude three weeks after relubrication needs a shorter interval or a higher-capacity grease reservoir. A bearing that holds baseline for six weeks after relubrication may be over-serviced at monthly intervals.

Oil Analysis for Oil-Lubricated Equipment

Oil analysis is the primary lubrication monitoring method for gearboxes, compressors, hydraulic systems, and oil-lubricated bearing housings. A sample drawn at regular intervals is sent to a laboratory for analysis.

Sampling frequency depends on criticality and oil change interval: monthly for critical equipment, quarterly for standard service. The sample point matters. Draw from the live oil zone, not a drain port where settled contamination gives a false reading. Use a vacuum pump and sample tube inserted to mid-depth in the sump.

Core Oil Analysis Tests

Reading the Results in Context

No single test value determines action. A viscosity increase combined with elevated acid number and darkening indicates oxidation. The same viscosity increase with elevated water content indicates contamination from a different source. The lab report provides data; the analyst determines what that combination means for this machine.

Establish baselines from new oil and from historical samples on the same equipment. Absolute limits from a chart may not apply to a specific machine with a specific oil type and operating profile. Trend data from the same unit is more informative than generic alarm thresholds.

Grease Selection and Compatibility

The right grease for a bearing depends on four operating variables. Matching all four prevents most selection errors.

Speed Factor

The viscosity grade must provide adequate film at operating temperature and speed. This is expressed as the speed factor nDm, where n equals RPM and D equals bore diameter in millimeters. High-speed bearings (nDm above 300,000) require lower-viscosity base oils to avoid churning losses. Low-speed, high-load bearings require higher viscosity to maintain film thickness under pressure.

Temperature Range

Base oil viscosity drops as temperature rises. The grease must maintain adequate film viscosity at the highest expected operating temperature, not just at ambient. For a motor bearing running at 80 C in a 40 C ambient, select a grease rated for continuous service above 100 C with drop point well above the upper operating limit.

Load Type

Radial loads on standard speeds: a standard mineral or synthetic grease without extreme pressure additives handles the load. High axial loads, shock loads, or slow oscillating motion: EP (extreme pressure) additive greases provide additional film support when the elastohydrodynamic film cannot form from speed alone.

Contamination Environment

Bearings in washdown environments, outdoor installations, or high-humidity areas require greases with high water resistance. NLGI 2 greases with lithium complex or calcium sulfonate thickeners perform better in water-contaminated environments than standard lithium greases. For sealed bearings, the seal material compatibility with the grease additive package must be confirmed with the manufacturer.

Compatibility Between Grease Types

Mixing incompatible greases can cause thickener structure collapse, resulting in oil separation and loss of lubrication properties. Lithium and polyurea thickeners are generally incompatible. Lithium and lithium complex are generally compatible but not always. Calcium sulfonate is broadly compatible with most thickener types but should still be confirmed before mixing.

Before switching grease types on a bearing, purge the old grease completely or consult the manufacturer's compatibility data. Adding the new grease on top of residual incompatible grease does not eliminate the risk; the contact zone at the rolling elements still contains the mixed product.

Setting Lubrication Intervals

Calendar-based intervals ignore the actual condition of the lubricant. The correct interval for a bearing depends on speed, temperature, load, contamination, and the grease's service life under those conditions.

Condition-Based Relubrication

Condition-based relubrication uses ultrasound amplitude to determine when to add grease. The trigger is a defined amplitude rise above baseline, not a date on a calendar. This approach adapts automatically to seasonal temperature changes, load variations, and grease degradation rate changes that fixed schedules cannot account for.

For a condition-based program: establish baseline amplitude on every lubricated bearing, set an alert threshold (typically 8 to 12 dBuV above baseline depending on the organization's tolerance), and relubricate when the threshold is crossed. The interval becomes self-calibrating over time.

Calculated Intervals as a Starting Point

For cases where condition-based monitoring is not yet in place, calculate the interval using the bearing speed factor (nDm) and apply correction factors for temperature, contamination level, shaft orientation (vertical shafts require shorter intervals than horizontal), and bearing type. Published formulas from bearing manufacturers provide a baseline calculation, with correction factor tables for each variable.

A calculated interval is a starting point. It does not account for the actual grease condition in service, which varies with the specific grease product, actual operating temperatures, and contamination exposure. Once a calculated interval is in place, ultrasound readings before each relubrication confirm whether the interval is appropriate or requires adjustment.

Use the Bearing Relubrication Interval Calculator as a starting point for interval setting.

Open Calculator

Continuous Lubrication Condition Data

Tractian's acoustic monitoring sensors track ultrasound amplitude on bearing housings continuously, providing the data to confirm lubrication condition between scheduled maintenance visits.

See Mechanical Monitoring
mechanicalmonitoring.com is an educational reference published by Tractian. Content covers principles, methods, and best practices for rotating equipment reliability. Always validate maintenance decisions against OEM documentation and qualified engineering review for your specific equipment and operating conditions.