Each oil analysis test measures something different. ICP spectrometry counts dissolved wear metals too small to see. Particle counting counts and sizes particles the spectrometer misses. FTIR identifies molecular species: oil degradation products, contamination types, additive depletion. No single test gives the complete picture.
ICP (Inductively Coupled Plasma) Spectrometry
ICP spectrometry measures dissolved metals and semi-metals in the oil sample at sub-micron scale, with results reported in parts per million (ppm). The instrument atomizes the oil sample in an argon plasma at approximately 6,000°C, then measures the emission spectrum of each element as it returns to ground state.
A critical limitation: only particles smaller than approximately 5 to 8 micrometers are reliably detected. Larger particles pass through the nebulizer without complete atomization and are therefore invisible to the spectrometer. This means ICP is most sensitive to early-stage wear, where fine sub-micron particles dominate, but may substantially underreport severe wear that produces large spall fragments or coarse debris.
The 20-plus elements typically reported fall into three functional groups:
- Wear metals: Fe (iron), Cu (copper), Al (aluminum), Cr (chromium), Ni (nickel), Pb (lead), Sn (tin), Ag (silver)
- Contamination indicators: Si (silicon, indicating dirt ingress), Na (sodium, indicating coolant or water), K (potassium, indicating coolant)
- Additive metals: B (boron), P (phosphorus), Zn (zinc), Ca (calcium), Mg (magnesium)
Additive metal trends matter as much as wear metal trends. A declining zinc or phosphorus reading indicates antiwear additive depletion. A calcium or magnesium increase can indicate contamination from an incompatible lubricant or coolant ingress.
The governing test standard is ASTM D5185. Most commercial laboratories run ICP as a core element in every standard oil analysis package.
Particle Counting and ISO Cleanliness
Laser particle counters measure the quantity and size distribution of solid particles suspended in the oil. Results are reported using the ISO 4406 cleanliness code: three numbers representing particles counted above 4, 6, and 14 micrometers per milliliter of oil, expressed as range codes where each code represents a doubling of concentration.
An ISO code of 17/15/12 means the oil contains approximately 640,000 to 1,280,000 particles per mL above 4 micrometers; 160,000 to 320,000 above 6 micrometers; and 20,000 to 40,000 above 14 micrometers. The three-number code is read in order from finest to coarsest.
Particle counting and ICP spectrometry are complementary, not interchangeable. Particle counting detects large particles that the ICP nebulizer cannot atomize. ICP detects fine dissolved metal that may not register as significant in a size distribution count. A machine producing catastrophic wear may show a sharply elevated particle count with relatively modest ICP values if the debris is primarily coarse.
Target cleanliness codes vary by system type. Hydraulic servo systems typically require ISO 16/14/11 or cleaner. Standard gear systems commonly target 17/15/12 or 18/16/13. The equipment manufacturer's specification is the authoritative reference. Trending matters as much as the absolute code: a system that has held 17/15/12 for two years and suddenly reads 20/18/15 warrants investigation regardless of whether the new value exceeds a generic alarm limit.
Analytical Ferrography
Ferrography separates magnetic (ferrous) particles from the oil by drawing the sample across a glass slide positioned over a strong magnetic gradient. The particles deposit along the slide in order of size and magnetic character, then the slide is fixed and examined under a bichromatic microscope.
Where particle counting tells you how many particles exist and ICP tells you which elements are present, ferrography reveals particle morphology: the physical shape, surface texture, and size of individual wear particles. Morphology identifies the mechanism producing the wear:
- Cutting wear particles: thin, curved, ribbon-like; indicate abrasive cutting, typically from a harder surface plowing through a softer one
- Fatigue spalls: flat platelets with smooth surfaces and irregular edges; produced by rolling contact fatigue in bearings or gear teeth
- Laminar particles: very thin, large-area flakes; produced by rubbing contact where surfaces repeatedly cold-weld and shear
- Spheres: near-perfect spherical particles; produced by electrical discharge machining (EDM) conditions or cavitation erosion
- Corrosive wear particles: irregular dark particles with surface pitting; indicate chemical attack rather than mechanical wear
Ferrography provides the highest diagnostic specificity of any oil analysis technique for identifying wear mechanisms. It is typically used as a follow-up test when ICP or particle count results indicate a problem requiring root cause identification, rather than as a routine screening test on every sample.
Viscosity Measurement
Kinematic viscosity is measured at 40°C and 100°C per ASTM D445. Both temperatures are measured because viscosity changes with temperature in a way that depends on the oil's formulation. The ratio between the two measurements allows calculation of the viscosity index (VI), which quantifies how much the oil thins as temperature rises. A higher VI means more stable viscosity across temperature extremes.
The lubricant's viscosity at operating temperature determines film thickness. A film that is too thin allows metal-to-metal contact; a film that is too thick increases fluid friction and heat generation. Both failure modes shorten equipment life.
Viscosity change from the new oil specification signals a specific problem type:
- Viscosity increase above 25% of new oil spec: indicates oxidation-derived thickening, contamination with a heavier lubricant, or accumulation of varnish and sludge precursors in solution
- Viscosity decrease: indicates fuel dilution (in diesel engines), shear degradation of polymeric viscosity index improver additives, or contamination with a lighter lubricant or solvent
- Viscosity decrease in hydraulic systems: warrants checking for water ingress in addition to fluid dilution, since small water concentrations can disproportionately reduce apparent viscosity in some formulations
Viscosity is one of the fastest and least expensive oil analysis tests to run, which is why it appears in every standard package regardless of equipment type.
Water Content: Karl Fischer Titration
Karl Fischer (KF) titration measures water content in parts per million by reacting the water in the oil sample with iodine in a precisely controlled electrochemical cell. The electrical charge required to consume all iodine is stoichiometrically proportional to the water present. KF is accurate to single-digit ppm levels and is the authoritative method for quantifying water in lubricants.
A field alternative, the crackle test, can detect water above approximately 500 ppm by placing a small oil sample on a hot plate at roughly 150°C and listening for crackling caused by steam formation. The crackle test is useful for rapid screening but cannot quantify water concentration.
Water in lubricating oil causes several failure mechanisms:
- Above 500 ppm: oil film strength decreases and corrosion risk increases, particularly for ferrous surfaces and copper-containing alloys
- Above 1,000 ppm: immediate investigation required; water at this level significantly accelerates fatigue in rolling element bearings
- At low temperatures: dissolved water can come out of solution and form free water or ice crystals that block filters, damage hydraulic servo valves, and cause cavitation in pump inlet lines
Common water ingress sources: failed shaft seals, heat exchanger tube leaks, condensation in large reservoir systems with wide temperature cycling, and process water contamination in paper mill or food processing environments.
FTIR (Fourier Transform Infrared Spectroscopy)
FTIR identifies molecular species in the oil by measuring which infrared wavelengths are absorbed by the sample. Each molecular bond type absorbs IR energy at a characteristic frequency, producing a spectrum that functions as a molecular fingerprint. The technique involves subtracting a baseline spectrum of fresh, unused oil from the used sample spectrum to reveal only what has changed during service.
The resulting difference spectrum can identify:
- Oxidation: a carbonyl peak growing at approximately 1,710 cm-1, indicating oxygen has reacted with oil molecules to form acids, aldehydes, and ketones
- Nitration: absorption at approximately 1,630 cm-1, indicating combustion gas blow-by past piston rings in engines; nitration products accelerate oxidation
- Glycol contamination: a distinctive absorption pattern indicating coolant (antifreeze) has entered the oil, typically through a failed head gasket or cracked block
- Soot content: quantified by the absorption baseline across the mid-infrared range; elevated soot in diesel engine oil indicates incomplete combustion or an overfull oil change interval
- Fuel dilution: lighter hydrocarbon absorption indicating unburned fuel is entering the crankcase
- Additive depletion: changes in characteristic peaks for zinc dithiophosphate antiwear additives, phenolic and amine antioxidants, and metal-based corrosion inhibitors
FTIR captures contamination types and degradation chemistry that elemental analysis (ICP) and viscosity measurement cannot identify. Glycol contamination, for example, may show only a modest sodium increase in ICP results while producing a definitive FTIR signature. Oxidation can increase viscosity, but only FTIR identifies which specific molecular degradation pathways are active.
TAN and TBN
Total Acid Number (TAN)
TAN, measured per ASTM D664, quantifies the acidity of the oil by determining how much potassium hydroxide (in milligrams) is required to neutralize the acid in one gram of oil. The result is expressed as mg KOH/g.
Fresh oil carries a baseline TAN from its additive package. As the oil oxidizes in service, acidic degradation products accumulate and TAN rises. The meaningful signal is the rate of increase relative to the fresh oil baseline, not the absolute value alone. A TAN that has doubled from its new oil value over a normal service interval indicates accelerated oxidation and warrants an oil change.
TAN is most commonly monitored in turbine oils, compressor oils, and other non-engine industrial lubricants that do not contain alkaline additive reserves.
Total Base Number (TBN)
TBN, measured per ASTM D2896, quantifies the alkaline reserve in engine oils. Engine oils are formulated with alkaline additives (typically calcium or magnesium sulfonates) that neutralize combustion-derived acids, primarily sulfuric acid from sulfur in fuel and nitric acid from combustion gas blow-by. TBN expresses how much acid the oil can still neutralize.
As the alkaline reserve is consumed in service, TBN declines. When TBN falls below approximately 30 to 50% of the new oil value, the oil's ability to neutralize incoming acids is largely exhausted and continued operation risks corrosive attack on bearing surfaces, cylinder liners, and ring grooves. The exact threshold varies by oil type and engine application; the equipment and lubricant manufacturer specifications govern.
TAN and TBN are not measured on the same oil type in the same way. TBN is an engine oil test. TAN is typically monitored in oils that have no alkaline reserve to track. Measuring both on the same sample is unusual but not impossible in certain formulations.
Test Package Selection by Equipment Type
No single test package fits every application. The table below shows common test combinations matched to equipment type, with the highest-priority tests listed first within each row.
| Equipment Type | Recommended Test Package | Priority Tests / Watch Points |
|---|---|---|
| Gearbox | ICP, viscosity, particle count, water (KF) | Fe and Cu trends, ISO cleanliness code, water ppm |
| Hydraulic system | Particle count, ICP, water (KF), viscosity | ISO code (cleanliness-critical), water ppm, Si (dirt ingress) |
| Diesel engine | ICP, viscosity, TBN, water (KF), FTIR | Fe and Cu wear, TBN depletion rate, fuel dilution (FTIR), soot |
| Compressor (reciprocating) | ICP, viscosity, particle count, TAN | Fe and Cu trends, viscosity increase (oxidation), TAN rise |
| Rolling element bearing (oil bath) | ICP, particle count, water (KF), viscosity | Fe trend, ISO code change, water above 500 ppm |
| Turbine (steam or gas) | ICP, viscosity, TAN, particle count, water (KF) | TAN rise rate, water ppm (steam turbines), ISO code |
Ferrography is not listed as a routine test for any equipment type because it is typically reserved as a follow-up diagnostic when ICP or particle count results indicate an active wear condition requiring mechanism identification.
Test package selection should also account for the failure modes that would be most costly for a given asset. For a hydraulic servo system controlling a critical production line, ISO cleanliness code is the priority test because fine particle contamination degrades servo valve response before any wear metals accumulate. For a large diesel engine in a remote location where oil change logistics are expensive, TBN monitoring combined with FTIR for fuel dilution and soot directly determines the economic optimum drain interval.
Continuous Oil Condition Monitoring
Lab-based oil sampling gives you a snapshot every few weeks. Tractian's condition monitoring sensors track oil temperature, vibration, and machine health continuously, so abnormal conditions are caught between sample intervals rather than discovered at the next scheduled lab report.
See Mechanical Monitoring