Pump Monitoring

Pump Seal and Impeller Monitoring

How to detect mechanical seal degradation and impeller wear in centrifugal pumps through vibration analysis, process parameter tracking, and barrier fluid system monitoring.

The Detection Window

A mechanical seal that is beginning to fail runs hotter and leaks microscopically before the leak becomes visible. An impeller losing material to erosion delivers less flow at the same speed, which shows up in the process data before it shows up in the vibration spectrum. Both conditions are detectable before they require emergency repair.

Mechanical Seal Failure Modes and Detection

A mechanical seal fails through one of several physical mechanisms. Each produces detectable signals through different monitoring channels. Knowing which signal to watch for which mechanism is what determines whether the failure is caught early or at breakdown.

Seal Face Temperature Rise (Thermal Indicator)

Mechanical seal faces generate heat from sliding contact between the rotating and stationary face materials. Normal heat generation is balanced by the barrier fluid or flush fluid cooling the faces. When the faces begin to wear unevenly, develop surface cracks from thermal shock, or run dry due to fluid film breakdown, the heat generation rate increases while cooling capacity stays the same.

A temperature sensor at the seal gland or on the seal housing detects this increase before the seal fails completely. The rate of temperature rise matters as much as the absolute level: a seal that is warming steadily over days is deteriorating. A seal that has run at stable temperature for months is healthy.

Thermal monitoring of mechanical seals is most effective when a baseline temperature is established under consistent operating conditions (same flow rate, same fluid temperature, same ambient) so that temperature increases are interpretable against a known normal.

Acoustic Ultrasound Amplitude Rise (Friction Indicator)

The sliding contact between seal faces generates ultrasonic energy in the 20 kHz to 100 kHz range. A healthy seal running with adequate fluid film produces low ultrasonic emission. A seal running dry, with contaminated faces, or with inadequate lubrication produces elevated ultrasonic emission from face-to-face contact.

Ultrasonic monitoring of mechanical seals can detect dry running events that last only seconds, before thermal damage is visible. This is particularly valuable on pumps that handle fluids prone to vaporization (hot condensate, volatile hydrocarbons) where momentary loss of the liquid fluid film is possible during process upsets.

Barrier Fluid Pressure Drop (Double Seal Indicator)

Double mechanical seals (API Plan 53A, 53B, 53C) use a barrier fluid maintained at higher pressure than the process fluid. The barrier fluid fills the space between the two seal faces, and any leakage from the inner seal face passes barrier fluid into the process rather than process fluid into the environment.

A pressure drop in the barrier fluid circuit indicates one of two things: leakage through the inner seal face (barrier fluid entering the process), or leakage through the outer seal face (barrier fluid leaking to atmosphere). Monitoring the barrier fluid pressure continuously detects this leakage before it is visible externally or before the seal pressure differential is lost entirely.

On seal support systems with a defined barrier fluid reservoir volume, a drop in reservoir level that is not explained by thermal contraction also indicates seal leakage.

Visible Leakage at the Gland

Visible leakage at the seal gland is a late-stage indicator. By the time liquid is dripping from the seal housing, the seal faces have already failed. For non-hazardous services where environmental release is acceptable at low rates, visible leakage is sometimes used as the trigger for seal replacement planning. For toxic, flammable, or environmentally regulated services, relying on visible leakage as the detection method is not acceptable. Earlier indicators (temperature, ultrasound, barrier fluid monitoring) are required.

Barrier Fluid Monitoring for Double Mechanical Seals

Double mechanical seals require a functioning seal support system (seal pot or pressurized barrier fluid supply) to operate correctly. The support system is as critical as the seal itself, and its monitoring is part of comprehensive seal condition monitoring.

Pressure Differential Between Barrier Fluid and Process

API 682 specifies that the barrier fluid pressure for Plan 53 arrangements must be maintained at a defined differential above the seal chamber pressure, typically 25 psi (1.7 bar) above stuffing box pressure. If the barrier fluid pressure drops below this differential, process fluid can push past the inner seal face and contaminate the barrier fluid.

A pressure transmitter on the barrier fluid circuit monitored against the seal chamber pressure (or against a calculated stuffing box pressure if no direct measurement is available) confirms the differential is maintained continuously. Alarms should be set to alert when the differential drops below the required minimum.

Barrier Fluid Flow Rate

On thermosiphon systems (Plan 52 or 53B without external pressure), the barrier fluid circulates by convection as it heats from seal face contact. A drop in circulation rate indicates reduced heat transfer, which means the seal faces are either running cooler (no fault) or the thermosiphon is losing efficiency (early fault). A flow indicator in the thermosiphon loop monitors this indirectly.

On forced-circulation systems, the flow rate is set by the circulation pump. A drop in barrier fluid flow rate despite the pump running indicates a blocked orifice or filter, or a developing leak from the barrier circuit.

Barrier Fluid Temperature

Barrier fluid temperature at the outlet of the seal pot (after it has absorbed heat from the seal faces) indicates how much heat the seal faces are generating. A rising outlet temperature at constant operating conditions means the seal faces are generating more friction heat, which indicates face wear or reduced lubrication. Alarm setpoints for barrier fluid temperature should be established relative to a baseline under normal operating conditions.

Impeller Wear Detection

Impeller wear is gradual and hydraulic in nature. The vibration spectrum rarely shows a clear impeller wear signature until wear is advanced. Process parameters provide earlier warning.

Head and Flow Loss at the Same Speed

A centrifugal pump's performance follows a characteristic curve: at a given speed, a specific head corresponds to a specific flow rate. Impeller wear reduces the hydraulic efficiency of the impeller, shifting the pump curve down. At the same speed and discharge pressure, the pump delivers less flow. At the same speed and flow rate, the pump delivers less head.

Tracking the operating point (head vs. flow) over time against the as-built pump curve identifies when the pump has drifted off its design curve. This requires measurement of suction and discharge pressure (to calculate head) and flow rate. The comparison is most meaningful when operating conditions (speed, fluid properties) are held constant or corrected to a standard condition.

Impeller wear that causes a 5 to 10 percent drop in pump efficiency is detectable through this method well before the impeller requires replacement. The pump is still operational, but the efficiency loss may justify a planned outage for inspection.

Vane Pass Frequency Change

The vane pass frequency (VPF) is the number of impeller vanes multiplied by the rotational frequency. In a healthy pump, the VPF appears in the vibration spectrum at a predictable amplitude. The relationship between the impeller vane tip and the volute cutwater generates this frequency: the pressure pulse as each vane passes the cutwater produces the VPF signal.

As the impeller wears and the running clearance between the vane tip and volute increases beyond the design tolerance, the pressure pulse at VPF changes in character. The amplitude at VPF may decrease (reduced pressure differential per vane pass) and the spectrum around VPF may become broader as the interaction becomes less regular. This spectral change is subtle and requires trending over time rather than point-in-time comparison to be interpretable.

Erosion Detected by Oil Analysis in Pump Sump

Wet-sump pumps (primarily vertical turbine pumps and some process pumps with flooded bearing housings) carry wear particles from impeller erosion in the bearing oil. Oil analysis on samples drawn from the pump sump detects increased iron or other material-specific elements that indicate erosion of wetted components. This method is more applicable to larger vertical turbine pumps in water service than to horizontal API 610 pumps, which have sealed bearing housings isolated from the process fluid.

Condition-Based Inspection Triggers

The monitoring data described above should drive inspection decisions rather than just generate alarms. Practical trigger criteria for planning a pump inspection:

These triggers should be calibrated to the specific pump, service, and consequence of failure. A pump in continuous process service with no installed spare warrants more conservative trigger criteria than a pump with an installed spare in non-critical service.

Documentation at Inspection

When a pump is pulled for inspection based on monitoring data, the inspection findings should be documented in a way that connects back to the monitoring signals that triggered the inspection. This creates the feedback loop that improves future trigger criteria.

Record at each inspection:

Fault Detection Summary

Fault Early Indicator Monitoring Method Confirm at Inspection
Mechanical seal face wear Rising seal gland temperature above baseline Temperature sensor at seal housing; thermal imaging Face surface condition; measure face gap and scoring
Seal face dry running Ultrasonic amplitude spike at seal gland Continuous or periodic ultrasonic measurement Thermal marking on seal faces; carbon face damage
Inner seal leakage (double seal) Barrier fluid pressure drop; contamination of barrier fluid sample Barrier fluid pressure transmitter; oil analysis of barrier fluid Inner seal face damage; process fluid in barrier fluid circuit
Outer seal leakage (double seal) Barrier fluid level drop; visible leakage at outer gland Reservoir level indicator; visual patrol Outer seal face damage; barrier fluid at gland
Impeller hydraulic wear Pump curve shift: lower head or flow at same speed Process flow meter and differential pressure tracking vs. pump curve Wear ring clearance measurement; vane tip erosion
Impeller volute clearance increase VPF amplitude decrease in vibration spectrum Vibration spectrum trending at VPF Impeller tip-to-cutwater clearance measurement
Impeller erosion from abrasives Gradual head loss; increased iron in oil analysis (wet sump pumps) Pump curve tracking; oil analysis where applicable Visual vane surface condition; vane thickness measurement
Seal support system degradation Rising barrier fluid outlet temperature; reduced thermosiphon circulation Barrier fluid temperature and flow rate monitoring Orifice condition; heat exchanger fouling; filter restriction

Condition Monitoring for Pump Assets

Vibration and temperature monitoring at pump bearing housings, with automatic fault detection and alarm routing to your maintenance team. Designed for continuous process pumps where failure consequence is high.

See Mechanical Monitoring
mechanicalmonitoring.com is an independent resource covering rotating equipment monitoring and condition-based maintenance. Product references are for informational purposes only. Verify all specifications with the vendor before purchasing. mechanicalmonitoring.com is operated by Tractian; see tractian.com for full product details.