Mechanical Monitoring

Shaft Alignment

Shaft alignment is the process of positioning a driver and driven machine so their centerlines are collinear under operating conditions, reducing cyclic forces on bearings, seals, and couplings.

Why It Matters

Misalignment is the second most common cause of rotating machinery failure after lubrication problems. A 0.25 mm parallel offset at 3,600 RPM generates cyclic bearing loads equivalent to adding several times the machine's own weight to the shaft twice per revolution.

What Is Shaft Alignment?

Shaft alignment ensures that the rotational centerline of a driver (typically a motor) and a driven machine (pump, compressor, fan, or gearbox) are collinear under operating conditions.

The phrase "under operating conditions" is critical. Thermal expansion, piping loads, and structural settling all shift shaft positions as a machine warms up and reaches steady state. The cold position measured during alignment is deliberately different from the operating position: technicians set the cold target to land at the correct running position once the machine reaches operating temperature.

A shaft that looks perfectly aligned at ambient temperature can be significantly misaligned when running. Alignment procedures account for these predictable offsets by calculating thermal growth corrections before setting the final target.

Types of Misalignment

Angular Misalignment

The shaft centerlines intersect at an angle. The coupling opens and closes on each revolution as the shafts rotate. This produces a cyclically varying load on the coupling and on the bearings near it.

Vibration signature: dominant 2x shaft speed peak in the axial direction. Angular misalignment also produces 1x in the axial direction. High axial vibration relative to radial is a reliable indicator of angular misalignment, particularly when 2x axial exceeds 1x axial amplitude.

Parallel (Offset) Misalignment

The shaft centerlines are parallel but not collinear; one shaft is laterally offset from the other. The coupling must flex on each revolution to accommodate the offset, generating a cyclic bending load at 2x shaft speed, primarily in the radial direction.

Vibration signature: 2x shaft speed radial, often with a 180-degree phase difference between the drive end and non-drive end bearings. In practice, most misalignment is a combination of angular and parallel components, so both axial and radial 2x peaks are commonly present.

Soft Foot

One or more machine feet do not make full contact with the base. When hold-down bolts are tightened, the machine frame distorts to close the gap. When the bolts are loosened for adjustment, the frame springs back, shifting the shaft position.

Soft foot must be corrected before any shaft alignment work begins. Any alignment set over a soft foot condition will change as bolts are tightened and loosened during the alignment process, making it impossible to achieve a stable result. Soft foot is identified by placing a dial indicator on the machine housing and monitoring movement as each hold-down bolt is alternately loosened and tightened.

Effects of Misalignment on Machine Life

Bearing fatigue. Misalignment imposes cyclic radial and axial loads at 1x and 2x shaft speed on top of normal operating loads. Bearing fatigue life (L10) is inversely proportional to the cube of the applied load for ball bearings and the tenth power of the load for roller bearings. A modest increase in cyclic load produces a disproportionate reduction in bearing life.

A 0.1 mm parallel offset at a motor-pump coupling running at 1,800 RPM can reduce bearing L10 life by 30 to 50% in a direct-coupled machine, depending on shaft stiffness and bearing type. At higher speeds the effect is more severe.

Seal wear. Shaft deflection at the seal face from cyclic misalignment loads causes uneven wear on mechanical seal faces. Seals designed for a shaft running true to its centerline experience accelerated wear and leakage when that centerline is repeatedly displaced each revolution.

Coupling wear and fatigue. Flexible couplings accommodate a limited amount of misalignment elastically. Continuous operation beyond the coupling's rated misalignment limit causes element fatigue, rubber degradation (for elastomeric types), and eventual coupling failure. Coupling failure at speed is a safety hazard.

Foundation and piping loads. The cyclically varying forces from a misaligned machine transmit through the base frame into the foundation and through the shaft into connected piping. Piping that appears properly supported can experience fatigue cracking at flanges and welds if it is also serving as a corrective load against a misaligned machine.

Power consumption. Misalignment introduces parasitic losses in the coupling. These losses are small relative to motor output in most cases but are measurable and continuous. Correctly aligned machines consistently show slightly lower motor current at the same load.

Alignment Measurement Methods

Three methods are in common industrial use, with accuracy and ease of use increasing from first to last.

Straightedge and Feeler Gauge

A straightedge is laid across the two coupling halves and the gap is measured with a feeler gauge. This gives a rough visual check of gross misalignment but cannot detect angular misalignment reliably. Resolution is limited by the technician's feel and the straightedge's rigidity.

Not adequate for precision alignment at speeds above 600 RPM. Useful only as a pre-check before mounting dial or laser tooling, or for checking gross coupling engagement.

Dial Indicators

The reverse indicator method mounts a dial gauge on each shaft, reading the opposite shaft's coupling hub as both shafts rotate together. This captures both parallel offset and angular misalignment in two planes simultaneously.

The face-and-rim method reads a single indicator against the coupling face (angular) and rim (parallel), rotating only the shaft being measured. Simpler to set up but more susceptible to errors from coupling runout.

Both methods require correction for indicator bar sag, which introduces a systematic error if not accounted for. Bar sag correction is calculated by mounting the bar horizontally and reading the indicator at the 12 o'clock and 6 o'clock positions without rotating the shaft. Dial indicator alignment is reliable and well-understood. Skilled technicians achieve results comparable to laser systems on routine jobs.

Laser Alignment

Two laser heads mount on shaft fixtures, one on each shaft. As the shafts rotate (or are rotated through a defined arc), the heads transmit position data to a display unit. The system calculates the required shim changes for vertical correction and horizontal move distances directly, in real time.

Resolution: 0.001 mm (0.04 mil). Modern systems display a live graphic of shaft positions, recommend specific shim thicknesses, and log results for records. Laser alignment eliminates bar sag error and significantly reduces measurement time compared to dial indicators.

Laser systems require clean shaft surfaces for fixture mounting and functioning laser paths with no obstructions. They are the standard method for critical rotating equipment and high-speed machinery.

Alignment Tolerances

Tolerances tighten as shaft speed increases because the cyclic load from a given misalignment increases with the square of shaft speed. A 0.05 mm parallel offset that produces acceptable bearing loads at 900 RPM generates four times the cyclic force at 1,800 RPM and sixteen times the force at 3,600 RPM.

Speed (RPM) Parallel Offset Limit Angular Misalignment Limit
600 0.20 mm (8 mils) 0.10°
900 0.13 mm (5 mils) 0.07°
1,800 0.08 mm (3 mils) 0.05°
3,600 0.05 mm (2 mils) 0.03°
7,200 0.025 mm (1 mil) 0.015°

These values apply to typical flexible couplings. Coupling manufacturers publish their own tolerance tables specific to coupling type and bore size. Gear couplings tolerate more misalignment than disc or diaphragm couplings. Always use the coupling manufacturer's tolerance as the governing limit when it is tighter than the general guideline above.

Use the Shaft Alignment Tolerance Calculator to find acceptable tolerance for your coupling type and shaft speed.

Open Calculator

Thermal Growth Correction

Machines expand as they heat up. The expansion is predictable and must be accounted for in the cold alignment target.

Cast iron and carbon steel have a coefficient of thermal expansion of approximately 11 to 12 micrometers per meter per degree Celsius (11 to 12 x 10-6 m/m/°C). A motor operating at 80°C above ambient temperature expands by approximately 0.011 mm per mm of shaft centerline height.

A motor with a 300 mm shaft centerline height expands about 0.33 mm upward at operating temperature. If no thermal correction is applied, the motor shaft centerline rises 0.33 mm relative to the pump shaft centerline during warmup, moving from "aligned" to misaligned in service.

The correction: set the cold alignment target with the motor shaft centerline deliberately low by the calculated thermal growth amount. The motor rises to correct position as it reaches operating temperature. Laser alignment systems have thermal growth compensation built in, allowing technicians to enter shaft centerline heights and operating temperatures; the system calculates the cold target offset automatically.

Driven machines also grow thermally. Pumps handling hot process fluid, compressors, and steam turbines can have larger thermal growth than their drivers. Both machine growths must be calculated and the net differential applied as the cold target offset.

The Alignment Procedure

The sequence below applies to direct-coupled motor-to-pump or motor-to-compressor alignments using laser or dial indicator tooling.

  1. Correct soft foot. Before touching any alignment adjustment, identify and correct all soft foot. Place a dial indicator against the machine housing and loosen each hold-down bolt in turn. Any movement greater than 0.05 mm indicates soft foot. Shim under the affected feet until all four feet are in solid contact and movement is eliminated.
  2. Rough align by straightedge. Check that the coupling halves are within a reasonable starting range before mounting precision tooling. Gross misalignment can exceed laser system range limits.
  3. Mount tooling. Attach laser heads or dial indicator brackets to clean shaft surfaces. Verify the fixtures are tight and have no play. For dial indicators, measure and record bar sag.
  4. Collect data and calculate corrections. Rotate the shafts through the required arc (typically 90-degree increments for dial indicators; continuous or three-point sweep for laser systems). The display unit or manual calculation gives required shim changes and horizontal moves.
  5. Correct vertical position. Add or remove shims under the motor feet to achieve the calculated vertical correction. Shims should be clean, flat, and the correct size to fully cover the foot. Stainless steel shims in standard thicknesses reduce long-term corrosion risk under the feet.
  6. Correct horizontal position. Move the motor laterally using jack bolts or a hydraulic pusher. Horizontal corrections are typically smaller than vertical and do not require retightening to check; move until within tolerance.
  7. Re-check and iterate. Re-read alignment after each correction. Adding shims or moving the machine changes the position; corrections interact. Repeat measurement and correction until both parallel offset and angular misalignment are within tolerance in all planes.
  8. Tighten hold-down bolts and verify. Tighten all hold-down bolts to specified torque in a cross pattern. Re-check alignment after tightening: bolt tightening can shift the machine, particularly if any soft foot remains. A final reading confirming within-tolerance position completes the job.

Document the as-found and as-left alignment readings along with shim sizes added or removed. These records allow trending over time and provide baseline data for the next alignment.

Monitor Misalignment Between Alignment Jobs

Tractian's condition monitoring continuously tracks 1x and 2x vibration components that indicate developing misalignment between maintenance alignment jobs.

See Mechanical Monitoring
Information on mechanicalmonitoring.com is provided for educational purposes. Always follow your organization's procedures, equipment manufacturer specifications, and applicable safety regulations when performing alignment work on rotating machinery.