Vibration Analysis

Vibration Analysis for AC Induction Motors

Measurement points, fault-specific vibration signatures, and how to interpret the spectrum for common AC induction motor faults including bearing defects, rotor eccentricity, and stator looseness.

Key Principle

Motor vibration analysis provides mechanical fault detection. MCSA provides electrical fault detection. Together they cover the complete failure mode space for an AC induction motor. Either alone leaves significant fault categories undetected.

Measurement Point Locations

Consistent measurement point selection is the single most controllable variable in motor vibration analysis. Analysts who measure at ad hoc locations produce data that cannot be trended or compared across routes.

Every AC induction motor requires measurements at two bearing housings: the drive end (DE) and the non-drive end (NDE). At each housing, three axes are collected: horizontal, vertical, and axial. That yields six measurement points per motor as the standard minimum.

Drive End (DE) Bearing Housing

The drive end bearing carries the overhung load from the coupled shaft or belt. It generates the highest vibration amplitudes for faults related to misalignment and belt drive forces.

Non-Drive End (NDE) Bearing Housing

The non-drive end bearing carries primarily the rotor weight with minimal external load. NDE readings are cleaner than DE readings and provide a useful baseline for comparing rotor-sourced faults against load-influenced readings.

What Each Axis Detects

Radial axes (horizontal and vertical) detect forces acting perpendicular to the shaft: imbalance, radial misalignment, bent shaft, looseness at the bearing housing, and electromagnetic forces that produce radial vibration.

Axial axis detects forces acting along the shaft: angular misalignment (which produces a moment force with strong axial component), thrust bearing defects, and helical gear mesh. Pure imbalance produces minimal axial vibration on a horizontal shaft; significant axial at 1x suggests misalignment rather than imbalance.

Fault Frequency Reference for AC Induction Motors

The table below lists the eight most common motor fault types, their primary vibration frequencies, the direction where the fault appears strongest, and the confirming indicator that reduces ambiguity with other faults.

Fault Primary Frequency Direction Confirming Indicator
Imbalance 1x running speed Radial (H and V); minimal axial Phase relationship stable at 90° between H and V; axial <25% of radial amplitude
Radial misalignment 1x and 2x running speed Radial (H or V dominant, depending on coupling plane) High 2x relative to 1x; compare phase across coupling in horizontal and vertical planes
Angular misalignment 1x and 2x running speed with strong axial component Axial dominant; elevated at both DE and NDE Axial amplitude approaches or exceeds radial; 180° phase difference across coupling in axial direction
Bearing outer race defect (BPFO) BPFO = (N/2) × RPM × (1 − (Bd/Pd) × cosα) Radial; strongest in load zone direction Sidebands at BPFO ± 1x; elevated noise floor around BPFO frequency; confirmed by envelope analysis
Bearing inner race defect (BPFI) BPFI = (N/2) × RPM × (1 + (Bd/Pd) × cosα) Radial Sidebands at BPFI ± 1x (modulated by shaft rotation); amplitude modulates at 1x as defect rotates through load zone
Bearing rolling element defect (BSF) BSF = (Pd/2Bd) × RPM × (1 − (Bd/Pd)² × cos²α) Radial BSF and harmonics; often accompanied by 2x BSF; envelope analysis more sensitive than raw spectrum for early-stage
Rotor eccentricity 2x line frequency with sidebands at ±slip frequency around running speed harmonics Radial Sidebands spaced at slip frequency (typically 1 to 3 Hz) around 1x and 2x; disappears on coast-down (electromagnetic origin); MCSA confirms rotor bar condition
Stator looseness / electromagnetically induced vibration 2x line frequency (120 Hz on 60 Hz supply; 100 Hz on 50 Hz supply) Radial; sometimes axial depending on stator orientation Amplitude drops immediately on power removal; does not persist through coast-down; constant regardless of load if stator fault, load-dependent if air gap eccentricity

N = number of rolling elements; Bd = ball diameter; Pd = pitch diameter; α = contact angle. Bearing fault frequencies are bearing-specific; use manufacturer geometry data or a bearing fault frequency calculator.

Distinguishing Mechanical from Electromagnetic Vibration

Several motor fault signatures overlap in frequency with electromagnetic sources. A 120 Hz vibration component (on 60 Hz supply) can indicate stator looseness, air gap eccentricity, or a structural resonance excited by magnetic forces. The spectrum alone cannot separate these.

The standard separation test: record a spectrum during normal powered operation, then remove power and capture a second spectrum during coast-down within the first two to three seconds after shutdown. Electromagnetic vibration disappears immediately when power is removed. Mechanical vibration persists through the coast-down and decays only as running speed decreases.

Practical execution requires either a high-speed data logger that can capture the transient coast-down or a second analyst ready to record the moment of shutdown. Single-channel handheld meters with slow averaging miss the coast-down window. Continuous monitoring systems capture this automatically.

If the 2x line frequency component drops to noise floor within one second of shutdown, the fault is electromagnetic in origin: stator looseness, air gap eccentricity, or a magnetized rotor. If it persists and decays with speed, the source is mechanical at a frequency that coincidentally aligns with 2x line frequency at that running speed.

VFD-Driven Motor Considerations

Variable frequency drives change the supply frequency to control motor speed. This creates two complications for vibration analysis.

First, the 2x line frequency vibration component is no longer fixed at 120 Hz. It tracks with the VFD output frequency. A motor running at 45 Hz output will show 2x line frequency vibration at 90 Hz, not 120 Hz. Analysts using fixed-frequency cursors will miss or misidentify this component.

Second, running speed itself varies. Bearing fault frequencies, which are multiples of running speed, shift as the drive setpoint changes. Trending requires normalizing data to a consistent speed or capturing speed simultaneously with vibration.

VFDs also introduce high-frequency switching noise from the drive's PWM output. This appears as spectral content at the drive's carrier frequency (typically 2 to 16 kHz) and can mask bearing fault signatures in the high-frequency range. Some analysts apply high-pass filtering above the drive switching frequency for envelope analysis on VFD-driven machines.

One advantage VFD operation provides: running the motor at multiple speeds allows the analyst to confirm whether a frequency component tracks with running speed (mechanical origin) or remains fixed (electrical or structural resonance origin).

How Motor Vibration Analysis Complements MCSA

Motor current signature analysis (MCSA) monitors the stator current waveform for frequency components that indicate rotor and stator electrical faults. Vibration analysis monitors the physical motion of the bearing housings for frequency components that indicate mechanical faults. The two techniques detect different failure modes with minimal overlap.

What Vibration Detects That MCSA Misses

What MCSA Detects That Vibration Misses

Shared Detection Zone

Air gap eccentricity and rotor eccentricity appear in both domains. Vibration shows sidebands around running speed harmonics; MCSA shows sidebands in the current spectrum. When both are present together, confidence in the diagnosis is high. When only one shows the signature, the fault may be at an early stage or the sensor placement may be limiting sensitivity.

Programs that run only vibration analysis miss broken rotor bar faults until the mechanical imbalance caused by the broken bar becomes large enough to show at 1x. That can take months. MCSA detects rotor bar degradation while the bar is cracking, not after it breaks.

Spectrum Interpretation: Practical Guidance

A motor vibration spectrum is interpreted in three frequency zones. The low-frequency zone (below 10 Hz) contains running speed, sub-synchronous components, and very low-speed faults. The mid-frequency zone (10 Hz to 1 kHz) contains running speed harmonics, bearing fault frequencies, and electrical forcing frequencies. The high-frequency zone (above 1 kHz) contains bearing stress waves and ultrasonic content relevant to early-stage bearing deterioration.

Start interpretation by identifying running speed in Hz (RPM divided by 60). Mark 1x, 2x, 3x, and 4x on the spectrum. Any energy at those cursor positions is related to shaft rotation. Then identify line frequency (50 or 60 Hz depending on supply) and mark 2x line frequency. Any component at that position warrants the coast-down test.

Calculate bearing fault frequencies from the bearing manufacturer's geometry and mark them on the spectrum. Peaks at those positions that persist and grow over successive measurements indicate bearing deterioration. Peaks present in one measurement but absent in the next are more likely noise or signal processing artifacts than true bearing faults.

The noise floor itself carries diagnostic information. A rising noise floor across the mid-frequency range, without discrete peaks, can indicate distributed bearing surface damage before distinct fault frequency peaks develop. Trend the overall RMS level alongside the spectral content to catch fault progression that has not yet produced a clean frequency signature.

Continuous Motor Vibration Monitoring

Tractian sensors mount directly on bearing housings and stream vibration data continuously, with automated fault detection for bearing defects, imbalance, misalignment, and electromagnetic faults.

See Mechanical Monitoring
mechanicalmonitoring.com is an educational reference site operated by Tractian. Content reflects general industry practice and engineering principles. Fault diagnosis for specific equipment requires site-specific measurement, analysis by a qualified vibration analyst, and correlation with operational data. No content on this site constitutes a maintenance recommendation for any specific machine or installation.