The sensor at the measurement point is the weakest link in any vibration monitoring system. A poorly selected or improperly mounted sensor produces data that looks valid but misses the fault frequencies that matter. Sensor selection starts with the frequency range and dynamic range required for the fault types you are monitoring.
The Three Primary Vibration Measurement Types
Vibration can be measured as displacement, velocity, or acceleration. Each quantity is relevant at a different frequency range, which determines which faults it can detect.
Displacement
Measured in micrometers (µm) or mils (thousandths of an inch), displacement describes peak-to-peak shaft motion. It is the relevant quantity at low frequencies, generally below 10 Hz. Proximity probes measure displacement directly and are used in shaft orbit analysis for large rotating machinery.
Velocity
Measured in mm/s or in/s RMS, velocity is the standard quantity for overall machine health assessment per ISO 10816. It is most useful in the 10 Hz to 1,000 Hz range. Traditional electromagnetic velocity sensors (seismic pickups) measure this directly; accelerometers derive velocity by integrating the acceleration signal.
Acceleration
Measured in g (gravitational units), acceleration is sensitive at high frequencies above 1,000 Hz. This is the relevant range for bearing and gear fault detection, where defect frequencies commonly fall between 1 kHz and 20 kHz depending on shaft speed and bearing geometry. Accelerometers are the primary sensor type for bearing fault detection.
| Measurement quantity | Units | Relevant frequency range | Primary application |
|---|---|---|---|
| Displacement | µm or mils | Below 10 Hz | Shaft orbit analysis, journal bearings |
| Velocity | mm/s or in/s RMS | 10 Hz to 1,000 Hz | Overall machine health per ISO 10816 |
| Acceleration | g | Above 1,000 Hz | Bearing and gear fault detection |
Accelerometers: The Industry Standard
Piezoelectric accelerometers are the most widely used vibration sensor for condition monitoring. A piezoelectric crystal generates an electrical charge proportional to the acceleration applied to it. The signal is then amplified and conditioned for the data acquisition system.
ICP (Integrated Circuit Piezoelectric) accelerometers include a built-in charge amplifier powered by constant current from the data collector. This simplifies wiring, reduces susceptibility to cable noise, and makes ICP the practical standard for industrial condition monitoring installations.
Key specifications to evaluate
- Sensitivity (mV/g): Higher sensitivity provides better resolution at low vibration amplitudes. Lower sensitivity extends dynamic range before the signal clips. Most general-purpose condition monitoring sensors use 100 mV/g.
- Frequency range: Defined at the -3 dB points. A sensor rated 0.5 to 10,000 Hz means amplitude accuracy stays within ±3 dB across that range. For bearing fault detection, confirm the upper limit covers bearing defect frequencies for your shaft speeds, which can reach 5 to 15 kHz on common industrial machines.
- Temperature rating: Standard sensors operate to 120°C. High-temperature versions extend to 260°C or beyond, which is needed for motors and process pumps in heated environments.
- Mounted resonance frequency: Every accelerometer has a resonance frequency at which its own mass-spring system amplifies the signal. Data collected above the sensor's mounted resonance frequency is unreliable. A typical 100 mV/g accelerometer stud-mounted to a steel surface may resonate at 20 to 30 kHz. Softer mounting methods push this resonance to lower frequencies.
Mounting Method and Its Effect on Frequency Response
The mounting method is as important as the sensor itself. A rigid, direct connection to the machine surface is required to transmit high-frequency vibration accurately. Each mounting step down in rigidity reduces the usable frequency range.
| Mounting method | Typical usable frequency | Notes |
|---|---|---|
| Steel stud (threaded) | Full range of sensor | Best available connection. Requires a drilled and tapped hole in the measurement surface. |
| Adhesive mount | Up to ~7,000 Hz | Practical for permanent installations where drilling is not possible. Surface preparation and adhesive quality determine the upper frequency limit. |
| Magnetic mount (permanent) | Up to ~5,000 Hz | Suitable for permanent wireless sensor installations and route-based work. Adequate for most fault frequencies below 2,000 Hz. |
| Magnetic mount (handheld) | Up to ~2,000 Hz | For survey measurements. Operator technique affects result consistency significantly. |
| Handheld probe (non-contact) | Up to ~1,000 Hz | Survey use only. High variability between measurements; not suitable for trending or fault analysis. |
| Extension cable mounted | Same as base sensor | Cable resonance can affect data above 5,000 Hz on cables exceeding one meter. |
For bearing fault detection and high-frequency analysis, stud mounting is the minimum practical standard. Magnetic mounts are acceptable for overall vibration trending and low-to-mid frequency fault work.
Velocity Sensors (Seismic Pickups)
Electromagnetic velocity sensors generate a voltage directly proportional to velocity by moving a coil through a magnetic field. No external power supply is required. They measure velocity in the native signal without integration.
The trade-off is frequency response. Typical electromagnetic velocity sensors operate from 10 Hz to 1,000 Hz. They have no useful response at the high frequencies required for bearing fault detection. They are common in legacy installations and some portable survey analyzers.
In most new continuous monitoring installations, velocity sensors have been replaced by accelerometers with integration electronics. Accelerometers cover the full frequency range from low-frequency imbalance to high-frequency bearing faults in a single sensor, reducing hardware complexity.
Proximity Probes (Eddy Current)
Proximity probes measure the gap between the probe tip and the surface of a rotating conductive shaft. They output a DC voltage proportional to that gap, measuring shaft displacement directly in µm or mils. They do not make contact with the shaft.
Proximity probes are the standard instrumentation for turbines, large compressors, and high-speed machinery operating above 3,600 RPM where shaft behavior inside fluid-film (journal) bearings is the primary diagnostic quantity. Two probes mounted 90 degrees apart around a shaft cross-section generate the shaft orbit data used to detect instability, rotor rub, and bearing degradation.
Requirements for proximity probe systems are specific: the shaft surface must be smooth, homogeneous, and free of residual magnetism or hard spots that affect the eddy current field. Calibration is required for each shaft material. Bently Nevada, now part of Baker Hughes, established the dominant technical standard for proximity probe systems used in machinery protection.
MEMS (Microelectromechanical Systems) Sensors
MEMS accelerometers fabricate a microscale spring-mass system directly onto a silicon chip using semiconductor manufacturing processes. The deflection of the proof mass under acceleration creates a measurable change in capacitance, which is digitized on-chip.
The practical advantages for condition monitoring are size, power consumption, and cost. MEMS sensors are small enough to integrate into wireless monitoring hardware, and their low power draw makes multi-year battery operation feasible without sacrificing continuous data collection.
The limitation compared to traditional piezoelectric sensors is sensitivity and high-frequency response. Most MEMS sensors used in industrial wireless hardware are suited for machinery operating at shaft speeds below 3,600 RPM and for fault detection in the 10 Hz to 5,000 Hz range. For applications requiring detection of high-frequency bearing defects on fast-spinning machinery, stud-mounted piezoelectric accelerometers remain the higher-resolution choice. MEMS sensor performance continues to improve, and the gap with traditional sensors narrows with each generation of hardware.
Sensor Selection Guide
Match the sensor type to the application based on machine speed, measurement access, fault types being monitored, and whether the installation is permanent or route-based.
| Application | Recommended sensor type | Mounting | Sensitivity |
|---|---|---|---|
| General rotating machinery condition monitoring | ICP accelerometer | Stud or adhesive | 100 mV/g |
| High-temperature locations (motors, process pumps) | High-temperature ICP accelerometer | Stud | 100 mV/g |
| Slow-speed machinery (below 60 RPM) | High-sensitivity accelerometer | Stud | 500 to 1,000 mV/g |
| High-speed machinery (above 10,000 RPM) | Low-mass accelerometer | Stud | 10 to 50 mV/g |
| Large turbines and compressors | Proximity probes plus accelerometers | Integrated OEM probe mounting | Per OEM specification |
| Wireless continuous monitoring | MEMS accelerometer (integrated hardware) | Adhesive or stud | Per product specification |
| Route-based survey measurements | Handheld ICP accelerometer | Magnetic or handheld probe | 100 mV/g |
Slow-speed machinery note
At shaft speeds below 60 RPM, fundamental vibration frequencies fall below 1 Hz. A standard 100 mV/g sensor may not resolve signals at this amplitude. High-sensitivity sensors in the 500 to 1,000 mV/g range provide the resolution needed, combined with extended low-frequency response down to 0.1 Hz or lower.
High-speed machinery note
On machinery spinning above 10,000 RPM, vibration amplitudes can be large enough to saturate a 100 mV/g sensor. Low-sensitivity sensors (10 to 50 mV/g) extend the dynamic range upward. Sensor mass also matters: a heavy sensor on a light rotor changes the machine's dynamic behavior. Specify low-mass accelerometers for high-speed spindles and precision machinery.
Wireless Sensors for Continuous Bearing Monitoring
Tractian's wireless MEMS sensors mount on bearing housings and transmit continuous vibration and temperature data, with stud-mount installation for full-spectrum fault detection.
See Mechanical Monitoring