A bearing beginning to fail produces friction-induced high-frequency sound at 20-100 kHz before it generates detectable low-frequency vibration. Ultrasound monitoring catches this earlier stage, giving teams more lead time to plan a bearing replacement on their schedule.
What Is Acoustic Monitoring?
Acoustic monitoring, specifically airborne ultrasound monitoring, uses sensors tuned to frequencies between 20 kHz and 100 kHz to detect sound produced by friction, turbulence, and electrical phenomena. These frequencies sit above the range of human hearing, which tops out around 20 kHz.
The sensor converts these ultrasonic signals to audible frequencies through a process called heterodyne conversion. A technician can hear the characteristic sounds of developing faults through headphones while simultaneously reading overall amplitude in dBµV on a display. The combination of audible feedback and a quantitative measurement makes acoustic monitoring effective for both initial detection and ongoing trending.
Unlike vibration analysis, which captures mechanical motion through accelerometers, acoustic monitoring captures sound pressure waves in the air or structure. This means it responds to different physical phenomena and at earlier fault stages for certain failure modes, particularly bearing lubrication breakdown and early asperity contact.
Why Ultrasound Detects Faults Earlier Than Vibration
Early-stage bearing defects generate high-frequency acoustic emission from two sources: asperity contact between rolling elements and raceways when the lubrication film is insufficient, and stress waves released as subsurface cracks propagate under load. Both mechanisms produce energy concentrated at 20-100 kHz.
At this point, the defect is typically too small to generate measurable vibration at bearing defect frequencies. Those vibration signals, such as ball pass frequency outer race (BPFO) or inner race (BPFI), appear in the 100-2,000 Hz range. A defect needs to be large enough that each rolling element passing over it generates an impulse strong enough to exceed the noise floor of the accelerometer and the signal processing chain.
This creates a useful diagnostic window. A bearing in early fault stage may show elevated ultrasound amplitude with no abnormality in vibration. A bearing in later-stage fault will show both elevated ultrasound and developing spectral components in vibration. Catching a bearing in the early ultrasound-only stage typically means weeks to months of additional warning time compared to waiting for vibration anomalies.
This advantage is most pronounced on slow-speed equipment. Below 100 RPM, bearing defect frequencies fall at or below 1-2 Hz, where accelerometers have poor inherent sensitivity and ambient structural vibration becomes significant interference. Ultrasound amplitude is not frequency-dependent in the same way, making it the preferred primary monitoring technique for slow-speed machinery.
What Acoustic Monitoring Detects
Bearing Condition
Friction between rolling elements and raceways generates ultrasound in proportion to lubrication film quality and surface condition. A well-lubricated bearing with undamaged surfaces produces a smooth, consistent ultrasound profile at a low baseline amplitude. As lubrication degrades or surface defects develop, amplitude increases and the character of the sound changes.
A single dBµV reading compared against an established baseline on the same measurement point provides an immediate indication of whether the bearing has degraded. An increase of 8 dBµV above baseline typically signals an advisory condition; 16 dBµV above baseline is used as an urgent action threshold in many programs. These threshold values are relative to each bearing's own baseline, which accounts for differences in speed, load, and installation geometry between measurement points.
Defects create impulsive bursts at defect frequencies. A technician listening through heterodyne audio can often distinguish a smooth hiss (healthy bearing), a grinding or clicking sound (rolling element or raceway defect), and a rushing or turbulent sound (excess grease).
Lubrication Monitoring
Ultrasound provides direct real-time feedback on lubrication condition, which no other measurement technique does with comparable immediacy. A well-lubricated bearing has a separated elastohydrodynamic film between rolling elements and raceways. When that film thins or breaks down, metal-to-metal contact generates friction noise in the ultrasonic range.
Over-lubricated bearings generate a characteristic "rushing" sound from excess grease churning through the rolling element assembly. Under-lubricated bearings generate friction noise from inadequate film separation. Both conditions are audible through heterodyne conversion and detectable as amplitude changes in dBµV.
This makes ultrasound a precise guide for lubrication tasks. A technician adds grease slowly while monitoring the ultrasound amplitude and audio character. When amplitude drops and the rushing sound subsides, the lubrication condition is optimal. Adding more grease after that point increases amplitude again, indicating churning. This approach eliminates guesswork from lubrication intervals and prevents the common failure mode of over-greasing sealed bearings.
Compressed Air and Gas Leaks
Turbulent flow through a leak orifice generates broadband ultrasound. Compressed air escaping through a small opening creates a turbulent jet that radiates ultrasonic energy in all directions. Ultrasound detectors locate these leaks in compressed air systems, pneumatic lines, and pressurized vessels that would otherwise be inaudible at distances greater than a few centimeters or in noisy production environments.
Steam lines and process gas systems can also be surveyed using the same approach. The directional sensitivity of an airborne ultrasound receiver allows a technician to scan along a pipe run, valve assembly, or connection point and pinpoint the leak source rather than identifying only that a leak exists somewhere in a system.
Compressed air leaks are a consistent source of energy waste in industrial facilities. Industry estimates suggest 20-30% of compressed air generated is lost to leakage. Ultrasound surveys make those leaks locatable and quantifiable.
Steam Trap Testing
Steam traps are designed to discharge condensate while holding steam in the system. A functioning trap opens cyclically as condensate accumulates and closes when steam reaches the valve. Ultrasound distinguishes these conditions clearly.
A working trap produces an intermittent flow sound corresponding to its open-close cycle. A failed-open trap produces continuous, high-amplitude flow sound because steam is passing through constantly. A blocked or failed-closed trap produces silence or very low amplitude because no flow is occurring. These three acoustic signatures allow a technician to assess an entire steam trap population systematically without requiring temperature measurements or invasive inspection.
Electrical Discharge
Arcing, corona discharge, and tracking in electrical switchgear, transformers, and high-voltage equipment generate characteristic ultrasonic signatures. Corona produces a steady high-frequency hiss; arcing produces sharp impulsive bursts; tracking (surface discharge along contaminated insulation) produces a crackling pattern.
Ultrasound is used as a preliminary screening tool for electrical cabinet inspections. A technician scans panels with an airborne receiver before opening them. If ultrasonic activity is detected, thermal imaging or more detailed investigation is warranted. This sequence reduces inspection time and prioritizes where infrared resources are deployed.
Acoustic Monitoring vs Vibration Analysis
The two techniques detect overlapping but distinct fault types at different stages. Understanding where each excels determines how they are used together in a monitoring program.
| Attribute | Acoustic (Ultrasound) | Vibration Analysis |
|---|---|---|
| Technology | Airborne/structure-borne sound at 20-100 kHz; heterodyne conversion to audio | Mechanical motion measured by accelerometer; frequency range typically 10 Hz to 20 kHz |
| Frequency range | 20-100 kHz (ultrasonic) | 10 Hz to 20 kHz (sonic and low-frequency mechanical) |
| Best fault stage | Early (lubrication breakdown, asperity contact before structural defects form) | Mid to late (defect large enough to generate measurable impulses at bearing defect frequencies) |
| Slow-speed bearing effectiveness (below 100 RPM) | High; amplitude detection not frequency-dependent in same way as vibration | Low; defect frequencies fall below 1-2 Hz, near accelerometer noise floor and ambient vibration |
| Lubrication feedback | Direct and real-time; audio character and amplitude change immediately with lubrication state | Indirect; lubrication state affects bearing defect frequency amplitudes but with less immediacy |
The two techniques are complementary. Ultrasound provides earlier warning for bearing defects and direct lubrication feedback. Vibration analysis provides richer fault diagnosis including fault type identification, severity progression tracking, and detection of imbalance, misalignment, looseness, and resonance. A bearing showing elevated ultrasound but normal vibration is an early-stage fault. The same bearing showing both elevated ultrasound and growing defect frequency components in vibration has progressed further. Using both measurements together gives a more complete picture of fault stage and rate of progression.
Equipment and Measurement Approach
A handheld ultrasound instrument consists of a sensor, a heterodyne converter, and a display. For bearing measurements, a contact probe is placed directly against the bearing housing. The probe's rigid tip couples to the structure and captures ultrasound conducted through the metal rather than relying on airborne propagation. For leak detection and electrical screening, an airborne receiver with a parabolic or standard focusing cup captures sound at a distance.
Measurement is expressed in dBµV, a logarithmic scale referenced to microvolts at the sensor output. The decibel scale means that an increase of 6 dBµV represents roughly double the amplitude, and 20 dBµV represents a tenfold increase.
Establishing a reliable baseline is the foundation of a bearing monitoring program. A baseline is recorded on each measurement point when the bearing is confirmed to be in good condition with proper lubrication. This baseline accounts for the specific speed, load, and installation geometry of that bearing. Alarm thresholds are then set relative to that baseline rather than as universal absolute values. Commonly used thresholds are +8 dBµV above baseline for an advisory alert and +16 dBµV for urgent action requiring near-term maintenance planning.
Heterodyne audio output runs continuously while measuring. The three key sounds a trained technician learns to recognize are: a smooth, consistent hiss (healthy, well-lubricated bearing), a grinding or clicking pattern (rolling element or raceway defect generating impulsive contact), and a rushing or turbulent noise (excess grease churning in the bearing assembly).
Slow-Speed Bearing Applications
Ultrasound's primary advantage over vibration analysis is most significant on machinery running below 100 RPM. This covers a wide range of industrial equipment: paper mill rolls, mixing vessels, cooling tower fans, conveyor head pulleys, kiln trunnions, and large gearbox output shafts.
At low speeds, bearing defect frequencies fall at or below 1-2 Hz. Accelerometers have inherent noise floors that make these frequencies difficult to measure reliably. Structural vibration from adjacent machinery, foot traffic, and building movement sits in the same low-frequency range and creates interference that can mask or mimic bearing signals. Processing techniques like envelope analysis and high-frequency resonance excitation help, but sensitivity remains limited compared to higher-speed applications.
A paper mill roll bearing running at 15 RPM generates detectable ultrasound from a defect that produces essentially no measurable vibration response. The friction and contact stress from the defect still generate high-frequency acoustic emission regardless of rotational speed. Ultrasound amplitude is sensitive to contact severity, not to how many times per second that contact repeats. This makes ultrasound the primary condition monitoring technique for slow-speed bearings, with vibration used as a supplement once the fault has progressed to a stage where it becomes detectable.
Measurement technique on slow-speed equipment requires patience. Because defect contact events occur infrequently at low RPM, a technician needs to hold the probe in place for at least one full revolution, and often several, to capture a representative reading. Some instruments support data logging over a dwell period to capture the maximum amplitude across multiple revolutions rather than relying on a single instantaneous reading.
Continuous Acoustic and Vibration Monitoring
Tractian's acoustic monitoring sensors continuously measure ultrasound amplitude on connected bearings, tracking lubrication condition and early fault indicators alongside vibration data.
See Mechanical Monitoring