Any alignment job started over a soft foot condition will fail. When a foot does not make full contact with the base, tightening that bolt pulls the machine frame into a distorted shape. The shaft moves. The alignment changes. Correcting soft foot first is not optional.
What Is Soft Foot?
Soft foot describes the condition where one or more feet of a machine do not lie flat against the baseplate when the hold-down bolts are loose. The gap can be uniform across the foot, angled from one edge to the other, or hidden beneath layers of corrosion, debris, or deformed shimming.
The problem is not the gap itself. The problem is what happens when the bolt is tightened. Tightening pulls the foot into contact, and because the foot was not flat to begin with, the machine frame must flex to close the gap. That flex distorts the machine housing, shifts the bearing seats, and moves the shaft position. Any measurement taken in that distorted state does not reflect where the shaft actually wants to sit when bolts are later loosened and retightened.
This is why soft foot check is the mandatory first step in any shaft alignment procedure. A machine with soft foot cannot be aligned repeatably until the foot condition is resolved.
The Physics of Frame Distortion
Rotating machines are built to close tolerances. Bearing bores, seal housings, and shaft journals are machined to micron-level precision with the assumption that the machine frame sits flat and stress-free on its base.
When a foot is soft, tightening its bolt introduces a bending moment into the machine frame. The frame is not a rigid body under these conditions: it deflects. Bearing bores that were round become slightly oval. The shaft, supported by those bearings, shifts in both the vertical and horizontal planes. The magnitude of the shift depends on the size of the foot gap, the stiffness of the frame, and the bolt torque applied.
In practice, a soft foot condition of 0.15 mm (6 mils) at one foot can move the shaft centerline by 0.05 to 0.10 mm at the coupling, enough to push an otherwise good alignment outside tolerance. The shift is also inconsistent: it varies with bolt torque, with how many bolts are tightened, and in what sequence.
The Four Types of Soft Foot
Parallel Soft Foot
The foot is elevated uniformly above the baseplate. All edges of the foot are at the same height above the base, so the gap is the same at every point under the foot. This is the simplest type to detect and correct.
Cause: Insufficient or missing shims, a base that was not properly machined or leveled, or shims that have been removed during a previous repair without being replaced.
Correction: Add a parallel shim of the measured gap thickness. The shim must be clean, flat, and the same size as the foot pad. Stainless steel shims are preferred over soft metals that deform under bolt load.
Angular Soft Foot
The foot is tilted relative to the baseplate. One edge makes contact; the opposite edge is elevated. The gap is zero at one side and at maximum at the other. When the bolt is tightened, the foot rocks into contact along one edge and the frame is loaded asymmetrically.
Cause: A foot pad that is not machined flat, a baseplate surface that is not flat under that foot, a previously applied parallel shim that is thicker on one side from deformation, or grout that has not cured uniformly.
Correction: A tapered shim that matches the angular gap profile. Tapered shims can be purchased or fabricated. The taper angle must be measured precisely: place a straightedge across the foot, measure the gap at both ends with feeler gauges, and calculate the required taper over the foot width. Using a parallel shim under an angular soft foot only converts the condition from angular to parallel with a residual gap.
Squishy Soft Foot
This type is the hardest to detect. The foot appears to make contact, but when the bolt is tightened the dial indicator shows inconsistent or multi-directional movement. The foot is not truly rigid against the base.
Cause: Corrosion between shims and the base or between the foot and the shim stack, a shim pack that has too many thin shims compressed together, deformed or buckled shims from previous over-torquing, cracked or deteriorated grout, or contamination (paint, scale, weld spatter) on the base surface.
Correction: Clean all mating surfaces. Inspect and replace any shims that are corroded, buckled, or deformed. If the grout beneath the base is the source, the repair is more involved: the machine must come off, the grout must be cut out, replaced, and allowed to cure fully before realignment. Limit shim stacks to four shims per foot whenever possible. More shims means more interfaces, and each interface adds compliance to the stack.
Induced Soft Foot (Pipe Strain)
Induced soft foot does not originate at the foot itself. It is caused by external forces transmitted through piping, conduit, or ductwork connected to the machine. A pump with its suction and discharge flanges bolted under pipe tension will have forces acting on its casing that pull or push the feet away from the base.
Cause: Piping that is not properly supported, thermally expanded pipe running to a pump that was aligned before the pipe was hot, inadequate flexibility in the pipe run, or flange connections assembled under tension because the pipe was misrouted during installation.
The dial indicator test for induced soft foot looks identical to the test for other types. The only way to distinguish pipe strain from a mechanical foot problem is to disconnect the pipe flanges (one at a time), repeat the soft foot check, and compare the readings. If a previously soft foot becomes solid after a flange is disconnected, that pipe is the source of the induced load.
Correction: Pipe strain cannot be fixed with shims. The pipe must be supported, re-routed, or re-spooled so it exerts no net force on the machine casing when the flange bolts are tightened. Target: the soft foot indicator reading should not change by more than 0.05 mm (2 mils) when the flange is connected versus disconnected. If pipe support changes require engineering review, flag the finding and do not proceed with alignment until the pipe loads are resolved.
Soft Foot Type Summary
| Soft Foot Type | Cause | Dial Indicator Reading Pattern | Correction Method |
|---|---|---|---|
| Parallel | Missing or insufficient shims; base not machined flat under that foot | Steady upward movement when bolt is loosened; consistent across full foot | Add a parallel shim equal to the measured gap |
| Angular | Foot pad or base surface not flat; uneven shim deformation | Movement when bolt is loosened; greater at one edge of foot than other | Install a tapered shim matched to the angular gap profile |
| Squishy | Corroded shim stack, crumbled grout, contaminated mating surfaces, too many thin shims | Erratic or multi-directional movement; reading does not settle at a stable value | Clean all surfaces, replace damaged shims, repair grout if affected; limit stack to 4 shims |
| Induced (pipe strain) | Piping connected under tension transmits external forces through flanges to machine casing | Soft foot reading changes when pipe flanges are connected vs. disconnected | Re-support or re-route pipe until flange connection causes less than 0.05 mm change in foot reading |
How to Detect Soft Foot
Dial Indicator Method
This is the standard procedure and can be performed with any dial test indicator (DTI) mounted on a magnetic base.
- Clean all foot pads and baseplate surfaces thoroughly.
- Tighten all four hold-down bolts to the specified torque.
- Mount the dial indicator on the machine frame directly above the foot to be checked. Position the indicator stem to read vertically downward on the frame, not on the foot pad itself.
- Zero the indicator.
- Loosen only the bolt on that foot. Do not disturb any other bolt.
- Record the indicator reading. Movement greater than 0.05 mm (2 mils) indicates soft foot on that foot.
- Retighten the bolt before moving to the next foot.
- Repeat for all four feet, one at a time.
Record the reading for each foot before making any corrections. Correcting one foot can affect the readings at adjacent feet, so the full picture is needed before shimming begins.
To distinguish angular from parallel soft foot, supplement the indicator check with a feeler gauge inserted under each edge of the foot while the bolt is loose. If the gap is the same on all sides, the condition is parallel. If the gap is larger on one side than the other, the condition is angular.
Laser Alignment System Soft Foot Check
Most modern laser shaft alignment tools include a dedicated soft foot measurement function. The procedure is the same as the manual method: all bolts tight, loosen one, record the system's measured shaft movement, retighten, move to next foot.
The laser system measures shaft movement rather than frame deflection at the foot. This is more directly relevant to alignment because it captures the actual shift in shaft position caused by the foot condition, not just the flex at the foot pad. Some systems display both the raw foot gap reading and the resulting shaft movement in a single view.
Results above the system's soft foot threshold (typically 0.05 mm or 2 mils) are flagged automatically. The system will usually prompt the technician to correct soft foot before proceeding to the alignment measurement phase.
One advantage of the laser check: if the system uses coupled sensors, it can detect how soft foot on one machine (the motor) affects the position of the driven machine through the coupling, which a foot-mounted dial indicator cannot show.
How to Correct Soft Foot: Shim Selection and Placement
The goal of shimming is to fill the gap so every foot makes full, flat contact with the base under zero bolt load. When that condition is achieved, tightening the bolt loads the base vertically without bending the frame.
Shim material. Use stainless steel shims. They resist corrosion, do not compress under load, and hold their thickness over time. Pre-cut stainless shims with a slotted opening for the bolt are the standard for production maintenance environments. Avoid aluminum, which deforms under bolt load, and avoid mixing metals that will create galvanic corrosion.
Shim thickness tolerance. Choose a shim that is within 0.025 mm (1 mil) of the measured gap. A shim that is too thick will create a new soft foot in the opposite direction. A shim that is too thin leaves a residual gap. If the measured gap is between standard shim sizes, use the next smaller size and verify with the dial indicator rather than guessing.
Shim stack depth. Keep the total stack to four shims or fewer per foot. Every interface between shims is a potential source of compliance. A single thick shim is more rigid than four thin shims of equivalent total thickness. If the required shim height is too large to achieve with four shims, machine the base or fabricate a dedicated spacer block, then limit the final trim shims to four.
Sequence for correcting multiple feet. Correct the foot with the largest gap first. Retighten that bolt, recheck all four feet, then move to the next largest. The reason: the frame is a connected structure. Correcting one foot changes the load path through the frame and can affect the apparent gap at other feet. Checking the full set of readings after each correction prevents over-shimming or under-shimming the remaining feet.
Final verification. After all corrections are complete, repeat the full four-foot dial indicator check. All four feet must read 0.05 mm (2 mils) or less before alignment measurements begin. If any foot still exceeds the threshold, iterate: check the foot type again, adjust shimming, and recheck.
Pipe Strain: When the Machine Is Not the Problem
Pipe strain deserves separate attention because its correction is fundamentally different from shimming. No amount of shimming fixes a force being applied through a connected pipe flange.
The standard test: with all hold-down bolts tight and all pipe flanges connected, perform the four-foot soft foot check and record readings. Then disconnect each pipe flange one at a time and recheck the feet. A change in foot reading when a flange is disconnected confirms that the pipe is transmitting force to the casing through that connection.
Common sources of pipe strain in pumping systems:
- Pipe run that is not supported close to the pump flange, allowing the pipe's own weight to hang from the connection
- Pipe that was aligned to the pump nozzle at ambient temperature and then expands thermally once the system is hot, pulling the pump casing upward or sideways
- Flange faces that are not parallel or co-planar, requiring the bolts to pull the pipe into position and loading the joint under tension
- Piping systems where the expansion loop is undersized or improperly placed, transmitting thermal growth directly into the machine nozzle
The acceptable limit for pipe strain is a change of no more than 0.05 mm (2 mils) in the soft foot indicator reading when any single flange is connected. If the change exceeds that, the pipe needs remediation before alignment proceeds. Documenting the measured pipe strain value in the alignment report is good practice: it creates a baseline for future troubleshooting if the machine returns with an alignment problem.
Why Soft Foot Must Be Corrected Before Any Alignment Measurement
The requirement to correct soft foot before alignment is not procedural caution. It is a direct consequence of how alignment tools work.
Laser alignment systems and dial indicator setups measure the position of the shaft. They calculate what shims need to be added or removed at each foot to bring the shafts into collinear position. Those calculations assume that the relationship between the foot and the shaft is fixed: move the foot by 0.10 mm and the shaft moves by a predictable amount.
Soft foot breaks that assumption. When a foot is soft, tightening or loosening its bolt changes the frame distortion and moves the shaft in an unpredictable direction. The alignment calculation uses foot-to-shaft geometry constants that are only valid when the frame is undistorted. Over a soft foot, those constants are wrong, and the calculated correction moves the shaft to the wrong place.
In practice, this shows up as alignment instability: a machine that appears aligned after one pass comes back out of tolerance after the bolts are re-torqued or after the machine has run for a short time. The technician re-checks alignment, finds it has shifted, re-aligns, and the problem repeats. The root cause is almost always an unresolved soft foot, either a mechanical foot problem or pipe strain.
Spending 20 minutes on a thorough soft foot check before taking any alignment measurement eliminates that cycle. It also protects the bearing housing bores and seal registers from the cyclic distortion that comes from running over a soft foot condition.
Frequently Asked Questions
What is the acceptable soft foot limit?
The widely used threshold is 0.05 mm (2 mils) of shaft or frame movement when any single hold-down bolt is loosened. Some precision applications with tight coupling tolerances or high-speed machines use 0.025 mm (1 mil) as the limit. Check the machine manufacturer's specifications if available; otherwise, 0.05 mm is the standard working threshold.
Can you align a machine and then correct soft foot later?
No. Correcting soft foot after alignment requires loosening and re-torquing the affected bolt, which shifts the shaft position. The alignment must be verified and corrected again after any soft foot remediation. The correct sequence is always: correct soft foot, verify all feet are within tolerance, then begin alignment.
How many shims per foot is too many?
More than four shims per foot introduces compliance into the stack. Each interface between shims is a source of micro-movement under bolt load and thermal cycling. If the total required shim height demands more than four shims, fabricate a single machined spacer block for the bulk of the height and limit the final trim shims to four or fewer on top of it.
Does thermal growth affect soft foot?
Thermal growth itself does not create soft foot, but it can reveal a pipe strain problem that was not present at ambient temperature. A pipe connected at ambient temperature with no strain can develop significant strain as the system heats up and the pipe expands. For hot systems, perform the pipe strain check at operating temperature as well as cold, or use expansion joints and flexible connections designed to isolate the machine nozzle from thermal pipe movement.
What is the difference between soft foot and a bad base?
Soft foot is a condition at one or more feet: the foot does not sit flat on the base. A bad base is a structural problem with the foundation or grout beneath the entire machine: the base itself is not level, not flat, or not rigidly anchored. A bad base can cause soft foot at multiple feet simultaneously, but shimming the feet does not fix the base. If all four feet show significant and inconsistent soft foot readings after cleaning and shim replacement, the base or grout should be inspected for cracking, voids, or anchor bolt failure before proceeding.
Monitor Shaft Health Continuously
Soft foot and misalignment cause the same vibration signatures as developing bearing faults. Tractian condition monitoring sensors detect both and alert your team before the machine fails.
See Mechanical Monitoring