Shaft Alignment

Types of Shaft Misalignment

A technical description of angular, parallel, and combined misalignment in rotating machinery, with vibration signatures, effects on machine components, and how each type is measured and corrected.

Key Principle

Most shaft misalignment is a combination of angular and parallel offset. Pure angular misalignment produces forces at 2x shaft speed in the axial direction. Pure parallel misalignment produces forces at 2x shaft speed in the radial direction. In practice, both are present simultaneously, and both must be corrected to achieve acceptable alignment.

Angular Misalignment Parallel (Offset) Misalignment α Centerlines converge at angle Vibration signature: dominant 2× axial Shaft 1 Shaft 2 offset Centerlines parallel, offset vertically Vibration signature: dominant 2× radial Shaft 1 Shaft 2 Shaft misalignment types. Angular: centerlines meet at angle. Parallel: centerlines offset but parallel. Most real cases involve both simultaneously.

Angular Misalignment

Angular misalignment occurs when two shaft centerlines intersect at an angle rather than being collinear. The shafts meet at a point, often near the coupling midplane, but their axes diverge on either side of that point.

The coupling compensates for this angle by deflecting with every shaft revolution. Each complete rotation produces two full bending cycles through the coupling, which is why angular misalignment generates vibration at twice running speed (2x RPM) in the axial direction.

Physics of Angular Misalignment Forces

As the coupling flexes through each revolution, it imposes oscillating axial thrust forces on both shaft ends. The magnitude of these forces depends on the angular offset and the coupling stiffness. For rigid couplings, even small angular offsets generate large axial loads. Flexible couplings reduce but do not eliminate these forces.

The force cycle completes twice per shaft revolution, producing the characteristic 2x frequency. Severe angular misalignment can also excite 3x and 4x harmonics as the coupling reaches its deflection limits.

Measurement

Angular misalignment is measured at the coupling as the difference in gap between the near side and far side of the coupling face, typically expressed in mils per inch (thousandths of an inch per inch of coupling diameter) or milliradians. Laser alignment systems measure the angular offset directly as a slope difference between the two shaft centerlines.

Vibration Signature

Parallel (Offset) Misalignment

Parallel misalignment, also called radial offset, occurs when two shaft centerlines are parallel but displaced from each other. The axes do not intersect; they run side by side at a fixed distance apart.

In this condition, the coupling must accommodate a cyclic radial displacement with every shaft revolution. As with angular misalignment, the coupling passes through maximum deflection twice per revolution, generating 2x radial vibration.

Physics of Parallel Offset Forces

The radial offset forces the coupling to articulate in the radial plane. This produces two reaction force peaks per revolution directed toward the coupling center, which is the source of the 2x radial signature.

Larger offsets produce higher radial forces and more pronounced 2x amplitude. The forces act in the plane of the offset, so they are directional. Horizontal offset produces vibration primarily in the horizontal plane; vertical offset produces it in the vertical plane.

Measurement

Parallel offset is measured as the perpendicular distance between the two shaft centerlines at the coupling plane, expressed in mils (thousandths of an inch) or millimeters. Laser alignment systems report this as the offset at the coupling face in both horizontal and vertical planes simultaneously.

Vibration Signature

Combined Misalignment

Combined misalignment is the condition most commonly found on real machines. Pure angular or pure parallel misalignment is the exception. When a machine is bolted to a baseplate with some angular error and some radial offset, both types are present simultaneously.

Combined misalignment produces 2x elevation in both the axial and radial planes. The relative magnitude of the axial versus radial 2x amplitude gives an indication of which component dominates, but this distinction is approximate and should be confirmed with direct measurement rather than inferred from vibration data alone.

Why Combined Misalignment Is the Default Case

Machine installation involves positioning a driven machine relative to a driver. Even with careful shimming and positioning, the two machines will have both an angle difference and a parallel offset between their shaft centerlines unless both are corrected. Correcting only one produces misalignment of the other type. The alignment procedure must address both simultaneously.

Identifying the Dominant Type from Vibration Data

When both types are present, vibration data can indicate which dominates. If axial 2x is substantially higher than radial 2x, angular misalignment is the larger contributor. If radial 2x dominates and axial is near-normal, parallel offset is the larger contributor. A 2x axial reading exceeding 50 percent of the 1x axial amplitude is a common threshold for flagging angular misalignment as significant.

Phase analysis adds confidence. Angular misalignment produces a 180-degree axial phase difference across the coupling. Parallel misalignment produces a 180-degree radial phase difference. Both present simultaneously means both phase relationships will be observed.

Soft Foot: The Prerequisite Problem

Soft foot is not a type of misalignment itself, but it prevents any alignment procedure from producing a valid result. It must be identified and corrected before alignment measurements are taken.

Soft foot occurs when one or more machine feet do not make full, flat contact with the baseplate. When the hold-down bolts are tightened, the machine frame distorts to conform to the baseplate surface. This distortion shifts the shaft centerline from its free-body position and introduces internal stresses in the machine casing that cannot be removed by shimming.

Types of Soft Foot

Detecting Soft Foot

The standard test is to loosen each hold-down bolt individually, one at a time, while monitoring shaft position with a dial indicator or the laser system. Movement greater than 0.002 inches (0.05 mm) when a bolt is loosened confirms soft foot at that location. The gap measurement before re-tightening quantifies the shim correction required.

Soft foot that is not corrected causes the shaft position to shift each time the machine is bolted down, making repeatable alignment impossible. It also generates elevated vibration from frame distortion, which can be misidentified as misalignment vibration.

Thermal Growth Offsets

Machines operating above ambient temperature expand as they heat up. The shaft centerline rises as the machine casing grows vertically. If alignment is performed cold and thermal growth is not accounted for, the machine will be misaligned at operating temperature even if it was aligned correctly at ambient.

Cold vs. Hot Alignment

Cold alignment sets the shaft position at ambient temperature before startup. Hot alignment accounts for the predicted thermal growth so that at operating temperature, the shafts are collinear. The cold alignment intentionally positions the driven machine shaft below the driver shaft centerline by the expected thermal growth amount.

The thermal growth of a machine is calculated using the formula: growth = C x L x delta T, where C is the thermal expansion coefficient for the casing material (approximately 6.5 x 10^-6 in/in/degF for carbon steel), L is the distance from the foot to the shaft centerline, and delta T is the temperature rise from ambient to operating. A machine with a 10-inch foot-to-shaft centerline height running 150 degF above ambient on a carbon steel frame will grow approximately 0.0098 inches vertically.

When Thermal Compensation Matters Most

Thermal compensation is most critical for steam turbines, high-temperature pumps, compressors, and any machine where the operating temperature differs significantly from ambient. For machines running at or near ambient temperature, the growth is small enough that standard alignment tolerances cover it. The dividing line is typically a temperature delta of 50 degF or greater at the casing.

Measuring Actual Thermal Growth

Calculation gives an estimate. Actual growth can differ due to non-uniform heating, piping forces, and casing geometry. Two direct measurement methods are used when precision is required:

How Misalignment Loads Bearings

The forces generated by misalignment pass through the coupling and into the adjacent bearings on both machines. The bearing closest to the coupling on each side carries the highest load.

Radial Loading from Parallel Offset

Parallel offset generates a radial force that rotates through the bearing races with each shaft revolution. The force peaks twice per revolution (2x). This cycling load causes uneven raceway wear, localized fatigue pitting, and reduced lubricant film thickness at the load zone. Bearings designed for steady radial loads experience dramatically shortened L10 life when subjected to this oscillating load pattern.

Axial Loading from Angular Misalignment

Angular misalignment generates oscillating axial thrust loads. Deep-groove ball bearings and cylindrical roller bearings are not designed to carry sustained axial loads. Even angular contact bearings and thrust bearings have axial load limits that can be exceeded by large angular offsets. The axial force reverses direction twice per revolution, which means the rolling elements are pushed back and forth across the raceway width, wearing the contact path and generating heat.

Combined Effect on Bearing Life

The ISO 281 L10 life calculation shows bearing fatigue life is inversely proportional to the cube of the load (for ball bearings) or to the 10/3 power of the load (for roller bearings). A bearing carrying twice its rated load has approximately 12.5 percent of its calculated L10 life for ball bearings. Misalignment-induced loads easily double or triple the dynamic equivalent load on nearby bearings, reducing life by an order of magnitude.

Misalignment in the Vibration Spectrum: Identification Guide

Vibration analysts identify misalignment from three sources of evidence: frequency spectrum, phase relationships, and time waveform. No single indicator is conclusive on its own.

Frequency Spectrum Indicators

Phase Analysis

Phase readings taken with a strobe or from a vibration analyzer confirm misalignment type. Measure phase at the inboard and outboard bearing housings on both machines in both axial and radial planes. Angular misalignment produces 180-degree phase shift between axial readings across the coupling. Parallel misalignment produces 180-degree phase shift between radial readings across the coupling. Both shifts present simultaneously confirms combined misalignment.

Time Waveform

The time waveform for misalignment typically shows a repeating pattern with two pulses per revolution. This double-pulse pattern corresponds to the twice-per-revolution coupling deflection cycle. The waveform is useful for distinguishing misalignment from other 2x sources such as looseness (which shows a more irregular pattern) or resonance (which shows a sustained sinusoidal pattern).

Comparison Table: Misalignment Types

Type Primary Vibration Signature Dominant Load on Bearings Phase Indicator Correction Method
Angular 2x RPM elevated axially; 1x axial also high Oscillating axial thrust at 1x and 2x 180-deg phase shift axially across coupling Adjust angular position of driven machine (shim under front or rear feet)
Parallel (Offset) 2x RPM elevated radially; 1x radial also high Rotating radial load at 1x and 2x 180-deg phase shift radially across coupling Translate driven machine horizontally or vertically (shim under all four feet equally, or shift laterally)
Combined 2x elevated in both axial and radial planes Both axial thrust and radial load elevated Both 180-deg phase shifts present Simultaneous angular and offset correction; must iterate until both are within tolerance
Soft Foot Variable; often mimics or masks misalignment Casing distortion loads; not from coupling forces Inconsistent phase; readings change with bolt torque sequence Shim under the affected foot to eliminate gap before alignment
Thermal Offset Misalignment vibration appears only at operating temperature Same as parallel offset once machine is hot Phase shifts visible only during operation, not at startup Pre-set cold alignment to compensate for calculated or measured growth

Correction Sequencing

A correct alignment procedure follows a fixed sequence. Deviating from this sequence wastes time and produces unreliable results.

  1. Check and correct soft foot first. All hold-down bolts must seat correctly before any shaft position measurements are taken.
  2. Rough alignment. Use a straightedge and feeler gauges to bring the machines close enough for the laser system to acquire targets.
  3. Mount the laser system and take an initial reading. Establish the baseline angular and offset values in both planes.
  4. Correct vertical angular misalignment. Add or remove shims under the front or rear feet of the driven machine to adjust the vertical angle.
  5. Correct vertical offset. Add or remove shims under all four feet simultaneously to raise or lower the driven machine.
  6. Correct horizontal angular misalignment. Shift the front or rear of the driven machine laterally using jack bolts.
  7. Correct horizontal offset. Translate the entire driven machine laterally.
  8. Verify and repeat. Each correction affects the other parameters. Iterate until both angular and offset values are within the tolerance specified for the coupling type and running speed.
  9. Apply thermal correction if required. Offset the final position by the calculated or measured thermal growth before final bolt tightening.

Detect Misalignment Between Scheduled Alignment Jobs

Tractian's vibration monitoring tracks 2x shaft speed amplitude and axial vibration, detecting misalignment development between scheduled alignment jobs.

See Mechanical Monitoring

Frequently Asked Questions

What is the difference between angular and parallel shaft misalignment?

Angular misalignment occurs when the centerlines of two shafts meet at an angle rather than being collinear. Parallel (offset) misalignment occurs when the shaft centerlines are parallel but displaced from each other in the radial plane. Angular misalignment produces dominant 2x axial vibration; parallel misalignment produces dominant 2x radial vibration. In practice, both types are almost always present simultaneously.

How does shaft misalignment appear in a vibration spectrum?

Misalignment typically appears as elevated 2x running speed (2x RPM) amplitude. Angular misalignment raises 2x in the axial direction; parallel misalignment raises 2x in the radial direction. A 2x axial reading greater than 50 percent of 1x axial amplitude is a strong indicator of angular misalignment. Severe cases also produce harmonics at 3x and 4x.

What is soft foot and why does it affect shaft alignment?

Soft foot is a condition where one or more machine feet do not make full, flat contact with the baseplate. When hold-down bolts are tightened, the machine frame distorts, shifting the shaft centerline and making accurate alignment impossible. It is identified by loosening each hold-down bolt individually and observing shaft or frame movement greater than 0.002 inches (0.05 mm). Soft foot must be corrected before any alignment measurement is taken.

What is thermal growth compensation in shaft alignment?

Thermal growth compensation accounts for the dimensional change as a machine heats from ambient to operating temperature. The shaft centerline rises as the casing expands. Alignment performed cold must intentionally offset the shaft position so that at operating temperature, the shafts are collinear. Compensation values are calculated from machine geometry, material properties, and the temperature delta between ambient and operating conditions.

How does misalignment damage bearings?

Misalignment imposes cyclic radial and axial forces on bearings at 1x and 2x running speed. Angular misalignment generates oscillating axial thrust loads that exceed bearing design limits. Parallel misalignment generates radial loads that rotate through the bearing races, causing uneven wear patterns. Both forms accelerate fatigue of rolling elements and raceways, reduce lubrication film thickness, and produce heat. The result is significantly shortened bearing L10 life.

MechanicalMonitoring.com is an educational resource for maintenance and reliability professionals. Content is for informational purposes only.
Always follow your equipment manufacturer's specifications and consult a qualified engineer for site-specific alignment procedures and tolerances.