Temperature is the last indicator to change as a bearing deteriorates, but it is the most reliable. A bearing that has been producing detectable vibration for months may show only a modest temperature rise until the final stage. That late-stage rise, tracked continuously, triggers an alarm before catastrophic failure.
What Thermal Monitoring Detects
Temperature monitoring provides a different view of asset health than vibration or electrical monitoring. It is primarily sensitive to energy-dissipation faults: friction from inadequate lubrication, resistance heating from electrical problems, and overloading.
It complements vibration monitoring for detecting bearing failures in their later stages and provides the early warning for lubrication-related failures. Three fault categories produce characteristic thermal signatures:
- Lubrication failure: Insufficient grease or oil allows metal-to-metal contact between rolling elements and raceways. The resulting friction generates heat at the bearing housing before the vibration signature becomes pronounced.
- Overloading: A bearing operating beyond its design load carries more stress per revolution. The increased contact stress generates heat even when lubrication is intact.
- Electrical resistance faults: Loose connections, corroded terminals, and failing insulation all increase resistance in the circuit. Current flowing through elevated resistance produces I2R heating concentrated at the fault point.
What thermal monitoring does not detect well: early-stage bearing defects (subsurface fatigue cracks before spalling), imbalance and misalignment in their early stages, and structural resonance. Vibration and acoustic methods are more sensitive to those failure modes.
Temperature Monitoring Technologies
| Technology | Measurement type | Accuracy | Application |
|---|---|---|---|
| RTD (Resistance Temperature Detector) | Contact, continuous | ±0.5-1°C | Permanent installation on bearing housings, motor windings |
| Thermocouple | Contact, continuous | ±1-2°C | High-temperature applications, process monitoring |
| Thermistor (NTC/PTC) | Contact, continuous | ±0.2-1°C | Precision applications, motor winding protection |
| Infrared thermometer (spot) | Non-contact, periodic | ±1-2% of reading | Route-based survey measurements |
| Thermal imaging camera (IR camera) | Non-contact, area image | ±2°C or ±2% | Periodic thermographic surveys of panels, bearings, equipment |
The choice between contact and non-contact measurement depends on access, safety, and whether continuous or periodic data is required. Critical assets with restricted access benefit from permanently installed contact sensors. Periodic thermographic surveys catch a wider range of equipment with less installed hardware.
Contact Temperature Monitoring: RTDs and Thermocouples
RTDs measure temperature through the predictable change in electrical resistance of a metal, typically platinum (Pt100 or Pt1000), with temperature. They are the most accurate contact temperature sensor type for industrial use. Resistance increases linearly with temperature, and the relationship is well-characterized, making RTDs well-suited for trending applications where small changes matter.
Thermocouples generate a voltage from the Seebeck effect at the junction of two dissimilar metals. They cover a wider temperature range than RTDs and are mechanically robust, but they are slightly less accurate and require cold-junction compensation. For bearing monitoring applications where the operating range is typically 20-120°C, either RTDs or thermocouples provide adequate accuracy; RTDs are generally preferred where accuracy and long-term stability are priorities.
For permanent installation on bearing housings, a spring-loaded RTD or thermocouple in a thermowell provides reliable continuous temperature measurement. The sensor should be positioned on the bearing housing as close as possible to the loaded zone of the bearing. Trending the absolute temperature and the rate of change over time provides early warning: a bearing in the later stages of fault progression typically shows a temperature increase rate that accelerates as failure approaches.
Installation Considerations
- Sensor location matters: the outer ring temperature at the load zone reflects bearing condition most accurately; a sensor on the opposite side of the housing will show a lower and more lagged reading.
- Ambient temperature changes can mask or mimic bearing temperature changes; use a reference sensor or compensate using ambient data when available.
- Lead wire resistance affects RTD accuracy at long cable runs; use three-wire or four-wire RTD connections to compensate.
- Thermowell material and design should match the application; stainless steel is standard for most industrial environments.
Infrared Thermography
Infrared cameras capture the thermal radiation emitted by surfaces and display it as a temperature map. The technique is non-contact, can survey large areas quickly, and identifies thermal anomalies invisible to other methods: hot spots on buswork inside a panel, a bearing housing running 15°C above its symmetrical pair, a coupling running hot from misalignment.
For mechanical equipment, thermography is most useful as a periodic survey tool. Walking the facility with a thermal camera identifies assets with elevated surface temperatures for follow-up investigation. For a motor-pump train, a thermographic survey might show the motor running within normal temperature range while the pump bearing housing is 25°C hotter than the motor bearing, pointing to a pump-side issue.
Emissivity and Measurement Accuracy
Thermal camera accuracy depends on the emissivity setting matching the surface being measured. Emissivity is the ratio of radiation emitted by a surface compared to a perfect blackbody at the same temperature. Polished metal surfaces have low emissivity (0.05-0.3) and reflect surrounding radiation, making them appear cooler than they are. Painted surfaces, rubber, and oxidized metals have higher emissivity (0.85-0.95) and give more accurate readings.
For reliable bearing housing temperature measurements with a thermal camera: use matte paint or temperature-indicating tape on the measurement point, enter the correct emissivity value, and subtract reflected ambient temperature when the environment is significantly hot or cold relative to the target.
Temperature as a Bearing Condition Indicator
Bearing temperature progression through fault stages follows a characteristic pattern. Understanding the stages prevents both missed alarms (alarm threshold too high) and nuisance trips (threshold too low).
Stage 1-2 (early fault): Temperature is typically unchanged or slightly elevated, 1-3°C above the healthy baseline. The fault is subsurface; contact conditions at the surface are not yet significantly different from a healthy bearing. Vibration and acoustic methods provide better sensitivity at this stage.
Stage 3 (advanced fault): Temperature begins to rise more consistently. The bearing is generating increasing friction heat from asperity contact and lubricant breakdown. A rise of 5-10°C above the established operating temperature warrants attention and should trigger increased monitoring frequency.
Stage 4 (critical): Temperature rises rapidly. The bearing is consuming lubricant and developing metal-to-metal contact over a larger area. Temperature may increase 20-50°C or more above normal. Failure is imminent.
Setting Alarm Levels
Establish the normal operating temperature for each bearing during a baseline period of stable operation under representative load. Use this baseline, not a generic table value, for alarm setting.
- First alarm: Baseline + 10°C. Initiate investigation; increase data collection frequency.
- Danger alarm: Baseline + 20°C. Plan immediate intervention; the asset should not continue operating without a defined run-to-failure decision.
- Rate-of-change alarm: A rise of 2°C per hour sustained over several hours is a significant warning sign regardless of absolute temperature. This catches accelerating degradation before the absolute threshold is reached.
Absolute temperature limits from bearing manufacturer data provide a cross-check: most standard rolling element bearings have a maximum operating temperature of 80-100°C at the outer ring. Exceeding these limits even briefly can damage the cage, rolling elements, and lubricant.
Motor Winding Temperature Monitoring
Motor windings have defined temperature classes based on the insulation system: Class A (105°C), Class B (130°C), Class F (155°C), and Class H (180°C). These are the maximum permissible temperatures for the winding hotspot during operation at rated load.
Exceeding the rated temperature accelerates insulation aging according to the Arrhenius model: approximately 50% reduction in insulation life per 10°C excess over the rated temperature. A Class F motor winding running continuously at 165°C instead of 155°C loses half its remaining insulation life. This makes winding temperature monitoring one of the highest-return monitoring investments for critical motors.
Winding temperature monitoring uses thermistors or RTDs embedded in the winding end turns at the factory. These are the most accurate measurement points because they are in direct thermal contact with the windings. For motors without factory-embedded sensors, surface-mounted sensors on the motor frame provide a reasonable proxy, with the understanding that frame temperature lags winding temperature by several degrees.
Most modern motor protection relays accept direct temperature inputs from embedded sensors and provide thermal model protection based on the measured temperature. Connecting these sensors to the protection relay and to the monitoring system gives both real-time protection and trending data.
Thermal Imaging for Electrical Equipment
Thermal cameras are standard tools for electrical panel inspections. Loose or corroded connections generate I2R heating; a connection with elevated resistance shows as a hot spot on a thermal image taken during normal load operation. The image captures the temperature differential between healthy connections and degraded ones without requiring the panel to be de-energized for inspection.
NFPA 70B and IEEE 43 reference thermographic inspection as part of electrical maintenance programs. The standard reporting framework uses delta-T (the temperature difference between a suspect connection and a reference connection under similar load):
- Delta-T 1-10°C: Monitor; consider follow-up inspection at next opportunity.
- Delta-T 10-40°C: First-level concern; schedule repair during planned downtime.
- Delta-T above 40°C: Priority repair; load reduction or immediate action depending on criticality.
Thermographic surveys of electrical equipment are most valuable when conducted under load conditions representative of normal operation, at minimum 40% of rated load. A survey conducted at low load will show smaller temperature differentials and may miss developing faults that only become significant under full operating conditions.
Continuous Thermal Monitoring with Tractian
Tractian's sensors include integrated temperature monitoring on bearing housings, trending thermal changes alongside vibration data to detect lubrication failure and bearing progression together.
See Mechanical Monitoring